Progress Thread My new 5.0 engine bay progress

Guccijayda · May 19, 2019

Hey guys this is a progress thread for my new garage queen 1988 foxbody mustang 5.0 stock bottom and stock top end as far as I know. Does sound like possibly has a mildcam. Please tell me if you see any other upgrades in the engine bay. Or if anything looks off. Its new to me too lol. Thanks all. Again my goals are to go take it to shows and get the engine bay looking and feeling like a winner. Hoping for respectable 350+ whp setup. I got a sharp pain in my gut when i see the blue paint chippin on the heads throttle body and the intake manifold...gotta go. I have three options. Trick flow top end kit. Super charger. Crate motor. Supporting mods and definitely couple nice gauges inside.My budget is 8 grand. Parts and labor guys since Im not a mechanic nor do I have the time!! (2 boys naggy wife and overtime)

Bbk longtubes
Bbk offroad h
Flows dumped
Msd distributor/ wires aftermarket coils
Bbk 70mm tb
Sve aluminim radiator
Dual electric fans on toggle switch
Hot air intake.... Gotta change that
6 point cage
Shortshifter not sure which brand
New King Cobra clutch feels like a heavy race clutch...
Aluminum driveshaft
15 inch drags and skinnies
Weld wheels
Cowl hood

Sure Im missing something

Guccijayda · May 20, 2019

Some more

Guccijayda · May 20, 2019

General karthief · May 20, 2019

Two boys, work and a nagging wife?
you need to learn to work on that car, it will be a stress reliever.

Guccijayda · May 20, 2019

General karthief said:
Two boys, work and a nagging wife?
you need to learn to work on that car, it will be a stress reliever.

Hahaha true true. I cant disagrree lol

Mustang5L5 · May 20, 2019

Id say go with the TFS kit and maybe a stroker kit. May not hit 350 whp but be pretty darn close.

You'll need to convert to mass air first, and camshafts with speed density tend to be difficult so hopefully there isn't one in there now. If so i'd put mass air at the top of your list

Guccijayda · May 20, 2019

Mustang5L5 said:
Id say go with the TFS kit and maybe a stroker kit. May not hit 350 whp but be pretty darn close.

You'll need to convert to mass air first, and camshafts with speed density tend to be difficult so hopefully there isn't one in there now. If so i'd put mass air at the top of your list

Thanks so much for your input bud. Im leaning towards the trick flow too. Stupid question. What is and how do I Know if im Mass air or speed density?

Dan02gt · May 20, 2019

Mustang5L5 said:
Id say go with the TFS kit and maybe a stroker kit. May not hit 350 whp but be pretty darn close.

You'll need to convert to mass air first, and camshafts with speed density tend to be difficult so hopefully there isn't one in there now. If so i'd put mass air at the top of your list

I agree with this. The top end kit will put you in neighborhood of 300 rwhp and make the car lots more fun to drive. Plus it's a great foundation if you want to add a blower later.

Unless your car is a CA car all '88s were speed density. If it had been converted you would have a MAF sensor connected behind your air filter, but your car is lacking that so it is still SD.

They look like this:

https://www.google.com/shopping/pro...ZeeQE3lmA,prmr:1,pid:8012900136493891129,cs:1

Mustang5L5 · May 20, 2019

Guccijayda said:
Thanks so much for your input bud. Im leaning towards the trick flow too. Stupid question. What is and how do I Know if im Mass air or speed density?

I don't see a mass air meter, so I assume its speed density.

Best way to tell is to look at the ECU in the pass kick panel area. There will be a 3 digit code that will identify the ECU.

Overall I see a fairly stock 5.0 without any major red flags. The previous owners choice of 70mm tb and egr spacer on a stock intake may have been a bit optimistic but one less part for you to buy for the TFS kit.

However, if it is speed density, first thing to do is swap to mass air. Requires buying the meter, the intake duct and a harness for the MAF and some minor repinning of the ECU harness

Guccijayda · May 20, 2019

Thanks so much guys! I had no clue. Now i see what you mean. Ill do some researching on mass flow sensors now.

deathb4dismount · May 22, 2019

That shifter looks like the SVE econo shifter. Meh, but as long as it has the set screws to limit shifter travel then I would run it and spend money else where. With that budget you have a lot of options and will get a lot of different opinions, think carefully about your combo and plan it out for how you want to drive rather than a HP number. Any info on the condition of the transmission? If you baby a T5 behind 300ish hp it should be fine, but with those drag radials you’re one hole shot or power shift away from a disaster. Here's what I would consider, new transmission (which cut your budget in half) then upgrade to mass air and build a top end with quality used parts to keep on your budget. Used TFS or AFR heads, custom cam, Systemax II. Like I said, a lot of different opinions.

Progress Thread My new 5.0 engine bay progress

Guccijayda

Member

Attachments

Guccijayda

Member

Attachments

Guccijayda

Member

Attachments

General karthief

wonder how much it would cost to ship you a pair

Guccijayda

Member

Mustang5L5

That is…until I whipped out my Bissell

Guccijayda

Member

Dan02gt

mazing how much gas smell came from that tiny hole

Mustang5L5

That is…until I whipped out my Bissell

Guccijayda

Member

deathb4dismount

Crap, didn’t realize my crotch was in that picture

Similar threads

Progress Thread My new 5.0 engine bay progress

Member

Attachments

Member

Attachments

Member

Attachments

wonder how much it would cost to ship you a pair

Member

That is…until I whipped out my Bissell

Member

mazing how much gas smell came from that tiny hole

That is…until I whipped out my Bissell

Member

Crap, didn’t realize my crotch was in that picture

Similar threads

Privacy & Transparency

Privacy & Transparency