Need help from a Pro.

bdollarbill

Member
Nov 27, 2005
89
0
6
Hello all im new to this forum but not to mustangs or Fords. for that matter. I recently purchased a 1990 Lx coupe. Really a good deal for the money spent & I feel like I got the better part of the deal. Here is spec's on the engine & my question following car info.

stock block bored .030 with trw forged pistons
Edelbrock 60259 aluminum heads
Crane 1.6 magnum rollers
Comp Cams hardened push rods with guide plates
Trickflow stage 2 cam
C&L 76mm Mass air
C&l Pro tube
Holley 80mm throttle body & egr spacer
Holley Systemax II Ported upper & lower intake
36Lb Ford injectors
Mac Direct fit hts coated shorties
Pro chamber 3" exhaust with flowmaster 40's with dumps

I think that is basic info so far the short block has under 3,000 miles on it, the owner of car pulled the upper end down to install the heads & intakes, when I purchased car the motor was disassembled from the heads up. the heads & holley systemax setup is like brand new doesn't even have any stains on them yet. I got all the upper end of motor togather & mounted the accessories including the distributor wires etc.. The car turns over fine & fires hot enough to knock you on your ass if holding the wire away from coil "speaking from first hand experience". But it doesnt seem to be getting any fuel through injectors? I have walbro 190lph pump & do not know what fuel pressure is set @ as I havent purchased a fuel pressure gauge yet. I know motor has good compression & is in time but not even a glimmer of a sound of trying to start. Any ideas???

Bill
 
when you turn the key forward (before it cranks over) do you hear the fuel pump kick on for a second?

If not, there is faulty wiring in your fuel pump.

If so, buy a gauge and fit it to the schrader valve on your fuel lines to know what fuel pressure you are running. Is you MAF sensor calibrated for 36 lbs injectors?
 
I'll try to "stall" until JRichker gets his No start checklist posted up.

As mentioned above, do you hear the fuel pump prime?

If not, you'll need to check to make sure the inertia switch isn't tripped (it's in the trunk of coupes by the shock, I believe. Also, check for a faulty Fuel Pump relay.

If your fuel pump primes, then you can use a tire pressure gauge to check for fuel pressure, just get a rag, put out the cigarette, and throw on some safety glasses because you may spray a little fuel.

If you have fuel pressure, can you smell fuel?

Are you 100% positive that the firing order is correct and going COUNTER-CLOCKWISE? Make sure you're using the 5.0 HO firing order, too. Also, are you 100% sure your timing is set properly? Stock timing is 10* BTDC. Is the SPOUT connector attached?
 
ok I difinately have fuel pressure as I hear the pump its pretty loud & I depressed the schjrader valve & its getting flow & some pressure just not sure how much. I know firing order is set up for HO engine compression is alright as far as I know when I was setting the lash on valves I left plugs in it semmed to be putting suffient pressure while turning will check with compression tester if It comes back it may be problem.
I also tried to get it to start by rotating dizzy as my wife turned engine over no luck.
Bill
 
I pulled the #1 plug just to double check engine was on #1 tdc on compression stroke & I smelled no signs of fuel, in chamber. Thats why im leaning towards A fuel pressure or injector problem.

There is no egr valve hooked up on car & I have several vacuum lines pluged just to try & get car fired. The vacuum line that goes to tree on firewall is plugg as well as the ones coming of connector on passenger side of car look like they went to smog pump or something.

Where should the vacuum line going to fuel pump be coming from? Maybe thats part of my problem?



Bill
 
The fuel pump is in the tank of the car and doesn't have a vacuum line going to it. The fuel pressure regulator is on the passenger side fuel rail behind the throttle body -- it needs to have a vacuum line going to it. But I don't think that will affect the whole system not getting fuel...it will just affect the pressure in the system; without a vacuum line connected it will run at a higher pressure at idle than it otherwise would.
 
bdollarbill said:
I pulled the #1 plug just to double check engine was on #1 tdc on compression stroke & I smelled no signs of fuel, in chamber. Thats why im leaning towards A fuel pressure or injector problem.

There is no egr valve hooked up on car & I have several vacuum lines pluged just to try & get car fired. The vacuum line that goes to tree on firewall is plugg as well as the ones coming of connector on passenger side of car look like they went to smog pump or something.

Where should the vacuum line going to fuel pump be coming from? Maybe thats part of my problem?



Bill
No vacum line for the f/p. You need to locate a line going into the manifold and spray in there.

If the plugs are dry, chances are the injectors are not firing or there is no pressure. Hence the suggestion of the carb spray.

Also if you have a test light, pull the #1 injector harness and have someone crank the engine while you probe the wires of the harness. One will be hot and should lite or pullsate. Or you can use a noid light if available.
 
Itwas a typo on the fuel pump vacuum hose I was referring to the fuel pressure regulator not the fuel pump itself. I have the vacuum line on the fuel pressure regulator hooked to a vacuum line but with not motor running there isnt going to have a vacuum on it yet so I figured it was out of the troubleshooting loop at the moment.

Pro50sc Im going out to f-with the car now will check the injector harness to see if its get juice & spray the carb cleaner in the intake vacuum line.

Bill
 
bdollarbill said:
Itwas a typo on the fuel pump vacuum hose I was referring to the fuel pressure regulator not the fuel pump itself. I have the vacuum line on the fuel pressure regulator hooked to a vacuum line but with not motor running there isnt going to have a vacuum on it yet so I figured it was out of the troubleshooting loop at the moment.

Pro50sc Im going out to f-with the car now will check the injector harness to see if its get juice & spray the carb cleaner in the intake vacuum line.

Bill
:nice: Keep us posted and good luck.
 
OK I'm getting somewhere now it trys to start with the carb cleaner sprayed into intake vacuum line so I know it wants to start. I checked the injector harness on #1 & it is hot on both wires while key on & while trying to start that is with a circuit tester light on it no a multimeter. What do I need to check now ??

Your help has me happier than I was when i woke up this morning,,,,,, I was ready to throw out the Efi stuff & go to my victor Jr & aed 750DP set-up ..Now Im looking forward to trying out the EFI setup

Bill
 
bdollarbill said:
OK I'm getting somewhere now it trys to start with the carb cleaner sprayed into intake vacuum line so I know it wants to start. I checked the injector harness on #1 & it is hot on both wires while key on & while trying to start that is with a circuit tester light on it no a multimeter. What do I need to check now ??

Your help has me happier than I was when i woke up this morning,,,,,, I was ready to throw out the Efi stuff & go to my victor Jr & aed 750DP set-up ..Now Im looking forward to trying out the EFI setup

Bill
did you check the injector harness with it plugged in or unplugged? If it was unplugged it should only have juice on one side. If it's plugged in then it would have it on both and should be grounded by the ecm.
 
I checked it with it plugged in. I know I really want to buy the Autometer hood mount f/p set up so I can get multi use out of it but my be forced to go buy a cheap gauge & adapter to find out f/p
 
bdollarbill said:
I checked it with it plugged in. I know I really want to buy the Autometer hood mount f/p set up so I can get multi use out of it but my be forced to go buy a cheap gauge & adapter to find out f/p
Ok most likely the injectors are firing and it's a f/pressure/pump problem. The reading is a must at this point. Can you borrow a guage from someone?