• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Need Help On Setup

  • Thread starter Thread starter erniet17
  • Start date Start date Dec 11, 2007

erniet17

Member
Oct 4, 2005
124
1
17
Dec 11, 2007
#1
  • Dec 11, 2007
  • #1
I have a 93 GT. I am looking to put a 302 together. I want an everyday driver but with some decent power and the capability to handle a s/c down the road. I also want to convert the car to a 5 speed. What is the best way to go as far as engine and are there any threads that have info on the swap? Thanks
 

strtrcr50

New Member
Jun 21, 2006
0
4
0
Previously from Dirty Jerzey exit 7a
Dec 11, 2007
#2
  • Dec 11, 2007
  • #2
What is your budget, and what kind of hp numbers are you trying to obtain?
 

erniet17

Member
Oct 4, 2005
124
1
17
Dec 11, 2007
#3
  • Dec 11, 2007
  • #3
Maybe a few grand. I would like to be in the 300's naturally.
 

strtrcr50

New Member
Jun 21, 2006
0
4
0
Previously from Dirty Jerzey exit 7a
Dec 11, 2007
#4
  • Dec 11, 2007
  • #4
Trick flow top end kit will be a little over 2k. And will get you in the 300's.
 

erniet17

Member
Oct 4, 2005
124
1
17
Dec 11, 2007
#5
  • Dec 11, 2007
  • #5
By top end you mean heads and intake? The main thing that I want to do is pull the engine and completely rebuild it. I want to throw in a custom cam and maybe bore a little bit. If I bore, I only need to get bigger pistons, correct? I had a setup a while back with 351 heads (not sure which ones) and a custom cam with full exhaust and intake and it ran pretty nicely. I just don't remember much. I got into the s197's (2 of them) but I sold them. There's nothing like having no payments. I really appreciate your help with this. Forgive my ignorance.
 

Fast63

New Member
Sep 20, 2007
717
0
0
Dec 11, 2007
#6
  • Dec 11, 2007
  • #6
top end means head/cam/intake/timing chain/valvetrain... If you bore it, you will need to get the pistons you want first, then bring them with the block when it gets bored so they can make sure they are fitting the bores to the pistons. If you are wanting a supercharger later on, you should probably get some lower compression pistons to get you around 8.5:1 compression, then get a trick flow top end kit or piece together another combo like AFR 185's, roller rockers, buy a timing chain, get a cam... I would hold off on getting a custom cam though until you have all your other parts the way you want it. A custom supercharger cam is usually much different than a custom N/A cam.
 

NKau

Founding Member
Dec 15, 2001
1,346
0
37
Jefferson, WI
Dec 11, 2007
#7
  • Dec 11, 2007
  • #7
The trick-flow h/c/i, or any other combination of good aluminum heads, intake and cam will get you what you want in terms of power. How many miles are on your current engine? If you still have good compression, I'd just put install the h/c/i and not worry about rebuilding

If your engine doesn't need an overbore, don't spend the money. Overboring in itself doesn't gain you anything for power; installing higher compression pistons accomplishes that. If you want to supercharge down the road, the factory pistons are forged, and will keep you at a boost friendly compression ratio. If you do rebuilid see what the bores are like before making any rash decisions.

The motor in my notch was out of an '87 GT with 155K on it, and was definitely beaten. The bores had minimal wear however, and I was able to reuse the factory rotating assembly after the crank was polished. This will save you a lot of money if you can get away with it.
 

erniet17

Member
Oct 4, 2005
124
1
17
Dec 11, 2007
#8
  • Dec 11, 2007
  • #8
The car has over 165k miles. I want an everyday, reliable street car. I want to replace every single gasket and seal. I also want to replace the oil pump. I might as well do it since the engine will be out. So Trickflows are the way to go??? What is the purpose of boring then if it doesn't give you more power? I have been told to bore 30 over thus bumping it to a 306 and running 9.5:1 compression with a s/c.
 

PUNISHER RACING

Active Member
Aug 27, 2007
1,124
0
36
FORD CITY, PA.
Dec 11, 2007
#9
  • Dec 11, 2007
  • #9
to clean up the block and make it round again and remove all lands and scratches that kill your cylinder pressure and power. if your cylinders are in good shape and check out to be good and round and pistons in good shape, there is always the hone and re-ring option. If it was mine I would get block done(bored,decked) crank cut and rods resized with good bolts. Throw in a set of TRW 2482's new bearings, 1011-2 h. gaskets and good h. bolts. A set of AFR 165 heads 60cc heads a good blower cam, Cobra, Ekplorer intake and get it done right and proper. Just my 2 cents take it for what its worth we run 11's with a s/c stocker!!!
 

5spd GT

"the 5.0 owns all"
Founding Member
Aug 7, 2002
9,516
6
99
Arkansas
Dec 11, 2007
#10
  • Dec 11, 2007
  • #10
Stroke is where the power is, not boring, unless you do a lot of boring, like what an aftermarket block can give you.

Dart, World, R302, etc.

If you want reliability, I say go with particular stroker rotating assemblies.

You can have a reliable 450hp at the engine.
 
You must log in or register to reply here.

Similar threads

Paint and Body Door Latch Issue
  • KRUISR
  • Oct 9, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
274
Fox 5.0 Mustang Tech Oct 15, 2026
General karthief
K
Engine Gt40p vs 180 procomp
  • Kleinjj27
  • Oct 27, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
509
Fox 5.0 Mustang Tech Nov 3, 2026
Kleinjj27
K
D
Electrical Weird door wiring issues
  • Dakar09
  • Oct 20, 2026
  • Fox 5.0 Mustang Tech
Replies
4
Views
207
Fox 5.0 Mustang Tech Oct 21, 2026
Dakar09
D
J
Wheels-Tires Need Some Help - Brakes Upgrade/Wheel fitment
  • jaygee15
  • Dec 8, 2025
  • Fox 5.0 Mustang Tech
  • 3 4 5
Replies
85
Views
4K
Fox 5.0 Mustang Tech Oct 6, 2026
jaygee15
J
S
4.6 spitting o-rings out of 2 injectors
  • skidad
  • Sep 30, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • 2 3 4
Replies
78
Views
2K
1996 - 2004 SN95 Mustang -General/Talk- Nov 4, 2026
skidad
S
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?