Need Help On Setup

erniet17

Member
Oct 4, 2005
124
1
17
I have a 93 GT. I am looking to put a 302 together. I want an everyday driver but with some decent power and the capability to handle a s/c down the road. I also want to convert the car to a 5 speed. What is the best way to go as far as engine and are there any threads that have info on the swap? Thanks
 
By top end you mean heads and intake? The main thing that I want to do is pull the engine and completely rebuild it. I want to throw in a custom cam and maybe bore a little bit. If I bore, I only need to get bigger pistons, correct? I had a setup a while back with 351 heads (not sure which ones) and a custom cam with full exhaust and intake and it ran pretty nicely. I just don't remember much. I got into the s197's (2 of them) but I sold them. There's nothing like having no payments. I really appreciate your help with this. Forgive my ignorance.
 
top end means head/cam/intake/timing chain/valvetrain... If you bore it, you will need to get the pistons you want first, then bring them with the block when it gets bored so they can make sure they are fitting the bores to the pistons. If you are wanting a supercharger later on, you should probably get some lower compression pistons to get you around 8.5:1 compression, then get a trick flow top end kit or piece together another combo like AFR 185's, roller rockers, buy a timing chain, get a cam... I would hold off on getting a custom cam though until you have all your other parts the way you want it. A custom supercharger cam is usually much different than a custom N/A cam.
 
The trick-flow h/c/i, or any other combination of good aluminum heads, intake and cam will get you what you want in terms of power. How many miles are on your current engine? If you still have good compression, I'd just put install the h/c/i and not worry about rebuilding

If your engine doesn't need an overbore, don't spend the money. Overboring in itself doesn't gain you anything for power; installing higher compression pistons accomplishes that. If you want to supercharge down the road, the factory pistons are forged, and will keep you at a boost friendly compression ratio. If you do rebuilid see what the bores are like before making any rash decisions.

The motor in my notch was out of an '87 GT with 155K on it, and was definitely beaten. The bores had minimal wear however, and I was able to reuse the factory rotating assembly after the crank was polished. This will save you a lot of money if you can get away with it.
 
The car has over 165k miles. I want an everyday, reliable street car. I want to replace every single gasket and seal. I also want to replace the oil pump. I might as well do it since the engine will be out. So Trickflows are the way to go??? What is the purpose of boring then if it doesn't give you more power? I have been told to bore 30 over thus bumping it to a 306 and running 9.5:1 compression with a s/c.
 
to clean up the block and make it round again and remove all lands and scratches that kill your cylinder pressure and power. if your cylinders are in good shape and check out to be good and round and pistons in good shape, there is always the hone and re-ring option. If it was mine I would get block done(bored,decked) crank cut and rods resized with good bolts. Throw in a set of TRW 2482's new bearings, 1011-2 h. gaskets and good h. bolts. A set of AFR 165 heads 60cc heads a good blower cam, Cobra, Ekplorer intake and get it done right and proper. Just my 2 cents take it for what its worth we run 11's with a s/c stocker!!!
 
Stroke is where the power is, not boring, unless you do a lot of boring, like what an aftermarket block can give you.

Dart, World, R302, etc.

If you want reliability, I say go with particular stroker rotating assemblies.

You can have a reliable 450hp at the engine.