• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Need help with Distributor

  • Thread starter Thread starter Roxy89
  • Start date Start date Mar 3, 2007

Roxy89

New Member
Nov 11, 2006
38
0
0
Mar 3, 2007
#1
  • Mar 3, 2007
  • #1
Ok so I have been having a problem with my stang giving me problems starting and rough acceleration every once in awhile. Sometimes it starts fine and runs perfect, other times it doesn't. So I have a couple questions. First of all I pulled out the distributor and realized that the bottom part has a little bit of play to it. About 1/8" of movement up and down if I move it. Is this normal, or should it be completely still. I have a pic of it here showing where the movement happens.


I also was wondering how it is to reinstall the distributor back in. I have read a couple different threads on this, but I can't seem to figure out what I am feeling for in the spark plug #1 when I am cranking the engine. Also, where is the balancer that I have to check the mark of. Sorry if these are lame questions, but I haven't had experience with this yet on my 5.0 but have some mechanical knowledge and would rather do it myself then pay someone else.

Any info is greatly appreciated. Thanks.
 
T

Trefty

Member
Aug 13, 2004
117
0
16
Mar 3, 2007
#2
  • Mar 3, 2007
  • #2
Roxy89 said:
I also was wondering how it is to reinstall the distributor back in. I have read a couple different threads on this, but I can't seem to figure out what I am feeling for in the spark plug #1 when I am cranking the engine. Also, where is the balancer that I have to check the mark of.
Click to expand...

To find top dead center you want to feel compression. You'll feel pressure coming out of the cylinder when you crank it. Another easy way is to use a straw, stick it in the cylinder until you can feel the top of the cylinder and crank the engine over by hand until you can feel that the cylinder is at it's highest point, just make sure that you are on the compression stroke and not exhaust or else you're timing will be out by 180*. Then check the that your timing marks are lined up on the balancer(balancer is located by the crank pulley, big rubber disc with a pointer beside it).
 

Roxy89

New Member
Nov 11, 2006
38
0
0
Mar 4, 2007
#3
  • Mar 4, 2007
  • #3
thanks,

anyone else have any advice or tips?
 

Roxy89

New Member
Nov 11, 2006
38
0
0
Mar 4, 2007
#4
  • Mar 4, 2007
  • #4
Trefty said:
To find top dead center you want to feel compression. You'll feel pressure coming out of the cylinder when you crank it. Another easy way is to use a straw, stick it in the cylinder until you can feel the top of the cylinder and crank the engine over by hand until you can feel that the cylinder is at it's highest point, just make sure that you are on the compression stroke and not exhaust or else you're timing will be out by 180*. Then check the that your timing marks are lined up on the balancer(balancer is located by the crank pulley, big rubber disc with a pointer beside it).
Click to expand...


Is there any way to tell if it's on the compression stroke, or is it more of a trial and error thing?
 
T

Trefty

Member
Aug 13, 2004
117
0
16
Mar 4, 2007
#5
  • Mar 4, 2007
  • #5
Roxy89 said:
Is there any way to tell if it's on the compression stroke, or is it more of a trial and error thing?
Click to expand...

Well if you are using the "finger on the spark plug hole" methos to determe TDC instead of using the straw method, you will feel compression on the compression stroke and nothing on the exhaust stroke.
 

Roxy89

New Member
Nov 11, 2006
38
0
0
Mar 4, 2007
#6
  • Mar 4, 2007
  • #6
Trefty said:
Well if you are using the "finger on the spark plug hole" methos to determe TDC instead of using the straw method, you will feel compression on the compression stroke and nothing on the exhaust stroke.
Click to expand...


Well when I use the finger on the hole method, it feels like it is sucking my finger in the hole, i thought it was supposed to feel like it was blowing it out. So would the feeling i am getting be the compression stroke?
 
T

Trefty

Member
Aug 13, 2004
117
0
16
Mar 4, 2007
#7
  • Mar 4, 2007
  • #7
Roxy89 said:
Well when I use the finger on the hole method, it feels like it is sucking my finger in the hole, i thought it was supposed to feel like it was blowing it out. So would the feeling i am getting be the compression stroke?
Click to expand...

Suck equals intake, blow equals compression.
 

Roxy89

New Member
Nov 11, 2006
38
0
0
Mar 4, 2007
#8
  • Mar 4, 2007
  • #8
Ok so I checked my distributor with a new one at the auto store and apparently the little up and down motion is normal. I also got it back installed and everything is running great. I don't have any pinging so my timing is fine for now, but I am going to try and advance it later. Thanks for your help.
 
You must log in or register to reply here.

Similar threads

Distributor installed wrong
  • djj62478
  • Jun 14, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
4
Views
352
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 21, 2026
CAMTWO1070
P
Fuel New Eldebrock 1406 problems 1985 GT 5.0
  • Paddyman
  • Oct 22, 2026
  • Fox 5.0 Mustang Tech
Replies
4
Views
184
Fox 5.0 Mustang Tech Nov 2, 2026
manicmechanic007
F
Fox 1990 Mustang GT 5.0 A9L – Engine suddenly shuts off but immediately restarts when key turned
  • FishermansFriend
  • Aug 9, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
16
Views
702
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 30, 2026
General karthief
R
Microsquirt tune for stroked 351W in a foxbody
  • roldy
  • Jul 26, 2026
  • Digital Self-tuning Forum
Replies
7
Views
444
Digital Self-tuning Forum Oct 25, 2026
roldy
R
B
Electrical Why does my fox body keep frying eecs
  • brandyn200
  • Jun 20, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
533
Fox 5.0 Mustang Tech Jun 25, 2026
AeroCoupe
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?