• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech

Need lotsa help with this MSD 6btm gadget

  • Thread starter Thread starter BlueOvalStangGT
  • Start date Start date May 15, 2004

BlueOvalStangGT

Active Member
Oct 27, 2003
2,849
0
46
Tampa Florida....USF!!!
May 15, 2004
#1
  • May 15, 2004
  • #1
Todays task is to get that lil red box in my car. on one side theres a green and purple wire/adapter, that hooks to my boost retard switch right? then on the same side theres a another adapter and a hose, i know not what to do with either. then on the other side there s a thick black, that goes to frame(ground) and the thick red goes to positive, right? I have this lil fuse box with the same wire, im guessing that hooks up with that thick red somewhere in between the box and the positve. Then theres a red/wite that goes to an adapter, dunno where that hooks up and then a black/ orange wires, dont know where that hooks up either. The box, i can mount that anywhere there room right? just drill 4 holes and bolt in? any ideas? thanks for making this not so aggravating(already punched a hole in my door cause of the crank pulley ) superchargers are alotta work....
 

94TURBO5 O

New Member
Mar 14, 2004
2,509
0
0
VA
May 15, 2004
#2
  • May 15, 2004
  • #2
I mounted mine on the rear firewall over top of the Master cylinder.
It is simple to install and a diagram should be on the back of the box.
Go Here If you need more detailed instructions.
 

BlueOvalStangGT

Active Member
Oct 27, 2003
2,849
0
46
Tampa Florida....USF!!!
May 15, 2004
#3
  • May 15, 2004
  • #3
What is this and where does it go(the black box with the yellow and black wires going to it?)



it says to connect the 1/8 tubing to a port on the intake manifold, which one? do i need a T? then it says if a boost guage is used T into this line. the line from my boost guage is really tiny so im not sure what im doing here. can some one educate me?
 

94TURBO5 O

New Member
Mar 14, 2004
2,509
0
0
VA
May 15, 2004
#4
  • May 15, 2004
  • #4
Go here to page 19 and instructions are there also.
I do not know what that black and yellow wire are for b/c mine does not have them. For your boost line, you need a black rubber vacuum hose from the BTM then run that into a T adapter from your intake or to the bypass valve line.
 

94TURBO5 O

New Member
Mar 14, 2004
2,509
0
0
VA
May 15, 2004
#5
  • May 15, 2004
  • #5
This is my set-up

This is the nipple you need to tap into.
One nipple is for you FP regulator, the other for the boost/bypass/BTM line

This is the bypass line that will T into the other nipple.



(brass T)

The top line in the center goes to my BTM
The bottom left line goes in to my intake nipple

(white tee)

The plastic line goes to my boost gauge
The other connects into my bypass valve hose.


 

BlueOvalStangGT

Active Member
Oct 27, 2003
2,849
0
46
Tampa Florida....USF!!!
May 15, 2004
#6
  • May 15, 2004
  • #6
what about the green/red hose that usually hooks into that nipple?
 

94TURBO5 O

New Member
Mar 14, 2004
2,509
0
0
VA
May 15, 2004
#7
  • May 15, 2004
  • #7
Cap it off, you don't need it anymore.
 

BlueOvalStangGT

Active Member
Oct 27, 2003
2,849
0
46
Tampa Florida....USF!!!
May 15, 2004
#8
  • May 15, 2004
  • #8
just the red or the green(forgot which one goes to egr)
 

BlueOvalStangGT

Active Member
Oct 27, 2003
2,849
0
46
Tampa Florida....USF!!!
May 15, 2004
#9
  • May 15, 2004
  • #9
is this where you want me to mount it? it seems only the top to screws will fit if i mount it there........\
 

BlueOvalStangGT

Active Member
Oct 27, 2003
2,849
0
46
Tampa Florida....USF!!!
May 15, 2004
#10
  • May 15, 2004
  • #10
can anyone answer my last question? props to 94sc50 for the help btw
 

94TURBO5 O

New Member
Mar 14, 2004
2,509
0
0
VA
May 15, 2004
#11
  • May 15, 2004
  • #11
That's where mine is mounted. I only used one screw in the top left. It seems to hold there with no problems for the last 2 years there.
I am not sure which goes into the EGR b/c I don't have one on my car.
 
You must log in or register to reply here.

Similar threads

Electrical 91 hatch wiring help needed
  • FastDriver
  • Apr 7, 2026
  • Fox 5.0 Mustang Tech
Replies
2
Views
143
Fox 5.0 Mustang Tech Apr 8, 2026
FastDriver
P
Electrical MSD box wiring for an 88 GT- few questions.
  • pindude80
  • Jul 20, 2024
  • Fox 5.0 Mustang Tech
Replies
3
Views
926
Fox 5.0 Mustang Tech Jul 25, 2024
pindude80
P
Drivetrain 83’ Glx convertible C5 Trans help!
  • JacksonJared2113
  • Dec 25, 2025
  • Fox 5.0 Mustang Tech
Replies
2
Views
354
Fox 5.0 Mustang Tech Dec 26, 2025
JacksonJared2113
0
V6 to V8 Swap info
  • 02_2v_Curtis
  • Jan 11, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
0
Views
646
1996 - 2004 SN95 Mustang -General/Talk- Jan 11, 2026
02_2v_Curtis
0
K
Engine 93 gt new 351 w moter put in and installing ace's kill shot EFI. It turns over but Wan't start? Need Help.
  • kimscales
  • Jun 1, 2024
  • Fox 5.0 Mustang Tech
Replies
1
Views
1K
Fox 5.0 Mustang Tech Jun 2, 2024
AeroCoupe
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?