• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Need some help with broken bolt before I snap

  • Thread starter Thread starter pwcracer
  • Start date Start date Aug 15, 2007

pwcracer

Founding Member
Jun 13, 2000
347
0
16
Hastings, MN, USA
Aug 15, 2007
#1
  • Aug 15, 2007
  • #1
I was installing my timing cover today, enjoying life when I noticed the bottom left bolt won't go it. I remove the cover and noticed the jackhole who sold me my shortblock failed to mention he snapped off the timing cover bolt in the hole.

No big deal I thought, I drilled a hole in the bolt and ran a bolt extractor in it, and snap, the extractor snapped in the bolt.. Now I am stuck! I can’t drill it, as it's hardened like a samurai sword, and I can’t really get in there to weld onto it.. (I already tried this several times, and only messed up the surrounding area. I have a couple of ideas,

If this is the side that requires a dowel, like the other, I was going to weld in a dowel.. I was then going to cut the head off a bolt and weld that into the dowel.. I would hopefully have a stud that I could throw a nut on and be done with it.

My second thought is to go get my dad’s plasma cutter and try and blast a hole in the bolt, and then retap it..

Any other ideas?? Could use some help, as I have been working on this the past 3-4 hours.
 

Attachments

  • cover.webp
    18.6 KB · Views: 192

bill302

Active Member
Nov 2, 2005
2,131
1
46
alabama,gadsden
Aug 15, 2007
#2
  • Aug 15, 2007
  • #2
is the motor out of the car? if so take it to a machine shop and let them extract the bolt...
 

5spd GT

"the 5.0 owns all"
Founding Member
Aug 7, 2002
9,516
6
99
Arkansas
Aug 15, 2007
#3
  • Aug 15, 2007
  • #3
By looking at the picture, it appears to be out...so the machine shop is a good idea, put the 'pressure' on them. They may have dealt with worse...

It just depends on how much money is worth your time and stress level...

Good Luck!
 
Z

Zenix

New Member
Mar 30, 2005
26
0
0
Aug 15, 2007
#4
  • Aug 15, 2007
  • #4
There is a drill bit that will go through the extractor. I believe it is carbide but I'm not sure on that. It is about 15 dollars a bit though. I would try that first.

Otherwise if you take it to a machine shop they can use a special tool made for removing broken taps from holes which kind of works like a welder and basically vaporizes the broken bolt using electricity. At least that is what I was told. Either way if the carbide drill bit doesn't work then I would bring it to a machine shop.
 

90_Red_LX

Member
Sep 29, 2003
668
5
19
Asheboro, NC
Aug 15, 2007
#5
  • Aug 15, 2007
  • #5
Zenix said:
There is a drill bit that will go through the extractor. I believe it is carbide but I'm not sure on that. It is about 15 dollars a bit though. I would try that first.

Otherwise if you take it to a machine shop they can use a special tool made for removing broken taps from holes which kind of works like a welder and basically vaporizes the broken bolt using electricity. At least that is what I was told. Either way if the carbide drill bit doesn't work then I would bring it to a machine shop.
Click to expand...

Plunge edm. basically you burn the bolt out with electricity. Very effective way especially if your dealing with some hard stuff (in this case the extractor.)
 
You must log in or register to reply here.

Similar threads

M
2001 v6 heater return pipe leak question
  • mnky99
  • Nov 11, 2025
  • SN95 V6 Mustang Tech
Replies
1
Views
394
SN95 V6 Mustang Tech Nov 11, 2025
mnky99
M
M
Progress Thread mnky99 2001 V6 evap core, ac compressor, heater core replacement
  • mnky99
  • Sep 5, 2025
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
1
Views
750
1996 - 2004 SN95 Mustang -General/Talk- Sep 5, 2025
mnky99
M
0
V6 to V8 Swap info
  • 02_2v_Curtis
  • Jan 11, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
2
Views
1K
1996 - 2004 SN95 Mustang -General/Talk- Oct 7, 2026
2v_johnny
2
S
I don know what im doing!
  • Sha_lala_pookie
  • May 5, 2025
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
11
Views
759
1965 - 1973 Classic Mustangs -General/Talk- May 11, 2025
Sha_lala_pookie
S
Electrical Innovate PSB-1 is DOA? Am I an idiot? All plausable. Please Help
  • Dontknowchit
  • Apr 26, 2025
  • Fox 5.0 Mustang Tech
Replies
1
Views
688
Fox 5.0 Mustang Tech Apr 26, 2025
Dontknowchit
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?