• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

new engine started but no oil pressure?

  • Thread starter Thread starter pwcracer
  • Start date Start date Sep 16, 2007

pwcracer

Founding Member
Jun 13, 2000
347
0
16
Hastings, MN, USA
Sep 16, 2007
#1
  • Sep 16, 2007
  • #1
I started my new engine, it ran very rough, and we noticed after about 30 secs it had no oil pressure. My helper also mentioned it looked like the dizzy was oscillating a bit. I pulled the dizzy out and everything looked ok. Is it possible that the end of the dizzy went along side the hex shaft for the oil pump?

I spun the shaft with a drill and it showed oil pressure on the dash..
 

ls1beater4eva

New Member
May 13, 2005
334
0
0
mooresville
Sep 16, 2007
#2
  • Sep 16, 2007
  • #2
is it a mechanical guage or electric? if its electric check and make sure that the wire didnt come off the sending unit, and as far as the dizz not being on the shaft u would know it bc the car wouldnt start bc you would have never be able to get the dizzy past the cam gear, check and make sure that you didnt blow a fuse for the dash guages.
 

68keyblr

20+ Year Stangneter
Mar 17, 2003
946
20
49
Arizona
Sep 16, 2007
#3
  • Sep 16, 2007
  • #3
When you say the distributor was "Oscillating a bit" - what does that mean?
 

pwcracer

Founding Member
Jun 13, 2000
347
0
16
Hastings, MN, USA
Sep 16, 2007
#4
  • Sep 16, 2007
  • #4
Its the guage on the dash, I had someone watch and when I spin the pump shaft with a drill it showed pressure..


It kind of wobbled around.. Its a new distrubutor too
 

BLOWN 5.0 FOX

Member
Apr 4, 2005
213
0
16
NORTH SHORE MA
Sep 16, 2007
#5
  • Sep 16, 2007
  • #5
sounds like your running the wrong dizzy gear. Pull the dizzy and inspect for damage. If the dizzy isnt spinning to the proper rpm, niether is your oil pump, and your car will run like crap.
 
You must log in or register to reply here.

Similar threads

Engine Looking for suggestions and or ideas
  • PonyGTrider
  • Aug 25, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
733
Fox 5.0 Mustang Tech Sep 7, 2026
PonyGTrider
B
Engine Another no start after washing engine bay
  • bruno
  • Apr 26, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
24
Views
1K
Fox 5.0 Mustang Tech May 7, 2026
AeroCoupe
Engine Gas in my oil
  • limp
  • Jun 15, 2025
  • Fox 5.0 Mustang Tech
  • 2
Replies
35
Views
2K
Fox 5.0 Mustang Tech May 16, 2026
Mindseye007
M
01 mustang 3.8 fuel pressure issue
  • Mhaley2006
  • May 29, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
4
Views
537
1996 - 2004 SN95 Mustang -General/Talk- Aug 9, 2026
JohnKay
J
H
Ongoing Battle With Hydraulic Lifters
  • hailer06
  • Jun 8, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
617
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 9, 2026
Noobz347
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?