• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

New S/C - codes 92 & 42 help!

  • Thread starter Thread starter Mike in Texas
  • Start date Start date Nov 1, 2008
  • 1
  • 2
Next
1 of 2 Next Last
M

Mike in Texas

New Member
Nov 7, 2005
121
1
0
Nov 1, 2008
#1
  • Nov 1, 2008
  • #1
Just installed a Paxton 1220, seemed to be running ok until I installed a 255 hp intake fuel pump and new plugs. Now I get codes 42, 92, and all cylinders show weak on the cylinder balance test. The car stumbles and backfires (sounds like through the exhast when given gas at low rpms). Fuel pressure is 40 at idle (vacuum off) new plugs are autolite 3924 gapped at .040. Car has an FMU and MSD ignition retard. Timing is 12, idles fine at 900 but like I said stumbles and pops at low rpm and doesn't seem to have the kick it should under boost (6psi @ 5500 rpm).

Any ideas? I will go for a dyno tune when I get the $ but would like to get it working OK for now.
 
M

Mike in Texas

New Member
Nov 7, 2005
121
1
0
Nov 3, 2008
#2
  • Nov 3, 2008
  • #2
Stumped

No ideas??? Are you guys as stumped as I am?
 

strtrcr50

New Member
Jun 21, 2006
0
4
0
Previously from Dirty Jerzey exit 7a
Nov 3, 2008
#3
  • Nov 3, 2008
  • #3
Bring the gap down on the plugs to .032 and try again. Also, I know a lot of people dislike the c&l mass air. Try clocking the mass air and see if it gets better or worse.
 

2000xp8

SN Certified Technician
Aug 8, 2003
8,075
1,658
194
NJ
Nov 3, 2008
#4
  • Nov 3, 2008
  • #4
strtrcr50 said:
Bring the gap down on the plugs to .032 and try again. Also, I know a lot of people dislike the c&l mass air. Try clocking the mass air and see if it gets better or worse.
Click to expand...

Agreed.
I really wouldn't be depending on the C&L all natural, so IMO it's even worse with a supercharger.
 
M

Mike in Texas

New Member
Nov 7, 2005
121
1
0
Nov 3, 2008
#5
  • Nov 3, 2008
  • #5
Thanks for Advice

I clocked the MAf, no change. I'm going to up the timing to 14* and see what that does, if that doesn't work I may change the meter, what MAF do you recommend.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Nov 3, 2008
#6
  • Nov 3, 2008
  • #6
What do you mean that all cylinders are weak on a CBT? Through how many steps did they each fail the test?

Have you replaced the dizzy anytime recently? Your injector timing might be off.........
 

hotcobra03

Active Member
Nov 29, 1999
969
4
39
poteet,tx
Nov 3, 2008
#7
  • Nov 3, 2008
  • #7
Hego signal left and right service code 42/92.also check map for vacuum leak
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Nov 3, 2008
#8
  • Nov 3, 2008
  • #8
hotcobra03 said:
Hego signal left and right service code 42/92.also check map for vacuum leak
Click to expand...

No factory MAP on a '90.
 

hotcobra03

Active Member
Nov 29, 1999
969
4
39
poteet,tx
Nov 3, 2008
#9
  • Nov 3, 2008
  • #9
Im in a 88 to 89 book should be close.42/92 is hego yes?and 90 would be (c.b.t.)?
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Nov 4, 2008
#10
  • Nov 4, 2008
  • #10
hotcobra03 said:
Im in a 88 to 89 book should be close.42/92 is hego yes?and 90 would be (c.b.t.)?
Click to expand...

I'm not sure if this was directed at me.

If so, yes, 42/92 are rich HEGO codes. 90 would be generated if all cylinders passed the CBT.
 

hotcobra03

Active Member
Nov 29, 1999
969
4
39
poteet,tx
Nov 4, 2008
#11
  • Nov 4, 2008
  • #11
Good as to mike have you changed 02s yet or they unpluged?
 
M

Mike in Texas

New Member
Nov 7, 2005
121
1
0
Nov 4, 2008
#12
  • Nov 4, 2008
  • #12
Thanks

Thanks for all the help. As far as I know the O2 are original, I checked the ACT and it is OK, I sprayed around the intake with carb cleaner and found no leaks. I upped the timing to 14# and the car runs better but still some small surge. I will recheck the codes tonight. Drove the car after the timing change and it runs some better, but still not much low rpm power.

One other thing, I have the vacuum to the ignition retard and the FMU coming form the line to the fuel pressure regulator, could that be a problem. If so, what would be the right source?

Thanks again for all the help.
 

hotcobra03

Active Member
Nov 29, 1999
969
4
39
poteet,tx
Nov 4, 2008
#13
  • Nov 4, 2008
  • #13
Now this is gettn good.dual diaphragm assembly.cant see any vacuum routes in book says it needs good direct source of vac 4 both lines.your ignition module have 2 blue plugs or 3 yellow
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Nov 4, 2008
#14
  • Nov 4, 2008
  • #14
Do not share the vac line to the FPR with anything else.
 
M

Mike in Texas

New Member
Nov 7, 2005
121
1
0
Nov 5, 2008
#15
  • Nov 5, 2008
  • #15
Thanks

Were is the best place to get the vacuum for the FMU and ignition retard? The manual says a direct source is best, but I can't find another another available source on my Cobra intake. Not sure about the question on blue plugs or yellow on the ignition retard, it's an MSD 5462 universal unit.
 

hotcobra03

Active Member
Nov 29, 1999
969
4
39
poteet,tx
Nov 5, 2008
#16
  • Nov 5, 2008
  • #16
Ok mike im not a pro here but sc 42 92 are engine running codes .they are o2s.thier job is fuel control.very first step in diagnosis h1 fuel pressure.stop. Their is a list of 14 things that can be at fault 4 false code other than cap wires ect...fuel in oil, fuel contamination.you just posted what you have done.Ding change o2s and recheck ur work. In step 1 make sure vacuum hose is on
 

hotcobra03

Active Member
Nov 29, 1999
969
4
39
poteet,tx
Nov 5, 2008
#17
  • Nov 5, 2008
  • #17
Mike hold on im missing 1 page off my book .i need to know how you got your codes exactly.koeo code?engine running self test code?continuous self test code? Im missing koeo code.i did search 4 obd1 code and got different description
 
M

Mike in Texas

New Member
Nov 7, 2005
121
1
0
Nov 6, 2008
#18
  • Nov 6, 2008
  • #18
Reply

I ran the code check off the check engine light. 1st I ran the KOEO and got 11, then I ran the KEOR with the "goose" test and got 42 and 92, then I ran the Cylinder balance test and got 1,2,3,4,5,6,7,8. I've run this test about 4 different time with the same results. I checked the fuel pressure with the vacuum off and plugged and got 40 #, I did look at it with the vacuum on but don't remember the reading, seems like it was 42#. I will check it tonight with the vacuum on. Is that the right way to set the pressure? Looks like replacing the O2s is next. Thanks for the help. Oh by the way the only dyno shop down here in Corpus Christi doesn't do tunes it only gives you the HP chart. What a deal, huh?
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Nov 6, 2008
#19
  • Nov 6, 2008
  • #19
The CBT codes you listed are incorrect. If you do get a code, re-run the test (you can do it twice more in the same session with differing critieria).

Do you have a WB?
 
M

Mike in Texas

New Member
Nov 7, 2005
121
1
0
Nov 6, 2008
#20
  • Nov 6, 2008
  • #20
reply

No wideband, I reran the CBT twice (in same session) and got all cylinders as bad both times. Will rerun and try 3 checks. The dyno guys said they had a WB so looks like I'll have to make some runs. $300 seems like a lot without a tune, but they're the only game in town.
 
  • 1
  • 2
Next
1 of 2 Next Last
You must log in or register to reply here.

Similar threads

2
Running very very rich
  • 2esoteric
  • Oct 31, 2025
  • Fox 5.0 Mustang Tech
Replies
4
Views
469
Fox 5.0 Mustang Tech Oct 31, 2025
Noobz347
K
Resolved Need some assistance. Holley Terminator X alongside H/C/I. Very rough/inconsistent idle
  • karhoot
  • Jun 6, 2026
  • Fox 5.0 Mustang Tech
Replies
0
Views
236
Fox 5.0 Mustang Tech Jun 6, 2026
karhoot
K
Engine Random Misfire at idle.
  • Gulftown980x
  • Jul 29, 2026
  • SN95 4.6L Mustang Tech
Replies
11
Views
613
SN95 4.6L Mustang Tech Jul 31, 2026
squeak93
8
Engine Rough idle and aggressive sputtering when accelerating
  • 88vertible
  • Aug 13, 2025
  • Fox 5.0 Mustang Tech
Replies
4
Views
1K
Fox 5.0 Mustang Tech Dec 13, 2025
Jarhead67
J
Engine 1990 LX 5.0L EFI Mustang Fuel Management Problems - HELP!
  • 5.0LXStanger
  • May 25, 2025
  • Fox 5.0 Mustang Tech
  • 2 3
Replies
45
Views
3K
Fox 5.0 Mustang Tech Jul 11, 2025
5.0LXStanger
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?