New S/C - codes 92 & 42 help!

Mike in Texas

New Member
Nov 7, 2005
121
1
0
Just installed a Paxton 1220, seemed to be running ok until I installed a 255 hp intake fuel pump and new plugs. Now I get codes 42, 92, and all cylinders show weak on the cylinder balance test. The car stumbles and backfires (sounds like through the exhast when given gas at low rpms). Fuel pressure is 40 at idle (vacuum off) new plugs are autolite 3924 gapped at .040. Car has an FMU and MSD ignition retard. Timing is 12, idles fine at 900 but like I said stumbles and pops at low rpm and doesn't seem to have the kick it should under boost (6psi @ 5500 rpm).

Any ideas? I will go for a dyno tune when I get the $ but would like to get it working OK for now.
 
Bring the gap down on the plugs to .032 and try again. Also, I know a lot of people dislike the c&l mass air. Try clocking the mass air and see if it gets better or worse.

Agreed.
I really wouldn't be depending on the C&L all natural, so IMO it's even worse with a supercharger.
 
What do you mean that all cylinders are weak on a CBT? Through how many steps did they each fail the test?

Have you replaced the dizzy anytime recently? Your injector timing might be off.........
 
Thanks

Thanks for all the help. As far as I know the O2 are original, I checked the ACT and it is OK, I sprayed around the intake with carb cleaner and found no leaks. I upped the timing to 14# and the car runs better but still some small surge. I will recheck the codes tonight. Drove the car after the timing change and it runs some better, but still not much low rpm power.

One other thing, I have the vacuum to the ignition retard and the FMU coming form the line to the fuel pressure regulator, could that be a problem. If so, what would be the right source?

Thanks again for all the help.
 
Thanks

Were is the best place to get the vacuum for the FMU and ignition retard? The manual says a direct source is best, but I can't find another another available source on my Cobra intake. Not sure about the question on blue plugs or yellow on the ignition retard, it's an MSD 5462 universal unit.
 
Ok mike im not a pro here but sc 42 92 are engine running codes .they are o2s.thier job is fuel control.very first step in diagnosis h1 fuel pressure.stop. Their is a list of 14 things that can be at fault 4 false code other than cap wires ect...fuel in oil, fuel contamination.you just posted what you have done.Ding change o2s and recheck ur work. In step 1 make sure vacuum hose is on
 
Mike hold on im missing 1 page off my book .i need to know how you got your codes exactly.koeo code?engine running self test code?continuous self test code? Im missing koeo code.i did search 4 obd1 code and got different description
 
Reply

I ran the code check off the check engine light. 1st I ran the KOEO and got 11, then I ran the KEOR with the "goose" test and got 42 and 92, then I ran the Cylinder balance test and got 1,2,3,4,5,6,7,8. I've run this test about 4 different time with the same results. I checked the fuel pressure with the vacuum off and plugged and got 40 #, I did look at it with the vacuum on but don't remember the reading, seems like it was 42#. I will check it tonight with the vacuum on. Is that the right way to set the pressure? Looks like replacing the O2s is next. Thanks for the help. Oh by the way the only dyno shop down here in Corpus Christi doesn't do tunes it only gives you the HP chart. What a deal, huh?
 
The CBT codes you listed are incorrect. If you do get a code, re-run the test (you can do it twice more in the same session with differing critieria).

Do you have a WB?
 
reply

No wideband, I reran the CBT twice (in same session) and got all cylinders as bad both times. Will rerun and try 3 checks. The dyno guys said they had a WB so looks like I'll have to make some runs. $300 seems like a lot without a tune, but they're the only game in town.