I was referred here by a gentlemen on TurboMustangs.com (a place I visit on a regular basis). I am in desparate need of help. I can't get my car running after days of trying. I think I have included all the pertinent information in the following paragraph (copied from my original post on tm.com). If you have any more questions, don't hesitate to ask. I want this thing running! Thanks in advance for any info you might be able to give me.
Ok, my car has been ready to start for a week and a half now. I still don't have an injector pulse. I have a '67 Mustang with an EFI 5.0L with a single MP T70. I am using a '88-'89 California (MAF) 5.0L harness. I have spent a few hours, in multiple sessions, on the phone with a gentlemen named Jeff at Ford Racing's Tech Line. He is extremely knowlegable about the EFI harnesses and complex wiring issues. Here is what I have learned from him. The TFI module sends a signal simultaneously to two places. One to the coil to let it know when to fire, and two, to the computer to tell the computer to switch the ground on to pulse the injector. Now, in wiring the harness, there are two wires (near the EEC connector) that must be spliced into to power up the harness. A red/blue wire and red/green wire. The red/blue wire gets a 12V run only source. The red/green wire gets power in both the crank and run situations. We have confirmed the proper operation of this by probing the 12V lead on the injector plug with a DVOM and seeing that in fact it does have 12V during crank and run key positions. Next, we tested the wires between the TFI module and the actual computer connector. I probed pin 16, 36, and 56 in the computer and verified continuity with the proper wire at the TFI module. All three had continuity. Next, we made sure the computer had the proper power and ground circuits for itself. Probing pin 40, 60, 37, 57 (maybe one other - have it written down at the shop) revealed that all circuits were intact and had power and ground at the appropritate places. We thought the computer itself might be bad. I installed my computer into a known running vehicle and it ran with no problems at all. I did the same thing with the TFI module. I also checked for any expanded pins at the computer connector. One seemed slightly large but did not change anything when squeezed back together. Our next idea is something is bad in the harness. My car has not been running for approximately six months. During this time, the computer was never disconnected. The engine has been out of the car and the wiring harness has been zip tied to the fire wall. Previous to this, the car was running just fine. I also tried cranking the engine over while I wiggled the wires on the firewall to possibly discover a short/broken circuit. This was to no avail either. I don't know what to do. For some reason the computer isn't receiving the signal from the TFI module so it can pulse the injectors. This is even though the wires between the TFI module and computer are good and have continuity. I am in the process of looking for a new harness to try (hard to come by). Does anyone have any ideas to help me get this thing going? It's killing me. Thanks.
Bryan
Ok, my car has been ready to start for a week and a half now. I still don't have an injector pulse. I have a '67 Mustang with an EFI 5.0L with a single MP T70. I am using a '88-'89 California (MAF) 5.0L harness. I have spent a few hours, in multiple sessions, on the phone with a gentlemen named Jeff at Ford Racing's Tech Line. He is extremely knowlegable about the EFI harnesses and complex wiring issues. Here is what I have learned from him. The TFI module sends a signal simultaneously to two places. One to the coil to let it know when to fire, and two, to the computer to tell the computer to switch the ground on to pulse the injector. Now, in wiring the harness, there are two wires (near the EEC connector) that must be spliced into to power up the harness. A red/blue wire and red/green wire. The red/blue wire gets a 12V run only source. The red/green wire gets power in both the crank and run situations. We have confirmed the proper operation of this by probing the 12V lead on the injector plug with a DVOM and seeing that in fact it does have 12V during crank and run key positions. Next, we tested the wires between the TFI module and the actual computer connector. I probed pin 16, 36, and 56 in the computer and verified continuity with the proper wire at the TFI module. All three had continuity. Next, we made sure the computer had the proper power and ground circuits for itself. Probing pin 40, 60, 37, 57 (maybe one other - have it written down at the shop) revealed that all circuits were intact and had power and ground at the appropritate places. We thought the computer itself might be bad. I installed my computer into a known running vehicle and it ran with no problems at all. I did the same thing with the TFI module. I also checked for any expanded pins at the computer connector. One seemed slightly large but did not change anything when squeezed back together. Our next idea is something is bad in the harness. My car has not been running for approximately six months. During this time, the computer was never disconnected. The engine has been out of the car and the wiring harness has been zip tied to the fire wall. Previous to this, the car was running just fine. I also tried cranking the engine over while I wiggled the wires on the firewall to possibly discover a short/broken circuit. This was to no avail either. I don't know what to do. For some reason the computer isn't receiving the signal from the TFI module so it can pulse the injectors. This is even though the wires between the TFI module and computer are good and have continuity. I am in the process of looking for a new harness to try (hard to come by). Does anyone have any ideas to help me get this thing going? It's killing me. Thanks.
Bryan