Noob saying Hi. Many questions also.

Lookin4Stang · May 23, 2007

Just saying Hi since I just registered. A little about myself. I drive a Mazda6 so i'm sorta a Ford guy but i'm currently saving up for a Mustang GT and have some questions. I have owned an LT1 Z28 and LS1 Z28 (I know ) in the past and did some modding to the LS1 but i'm totally in the dark when it comes to the 4.6 GT. I would like to get an auto (yes, the wife will be driving it too) and have read thru the forums for a while and am confused. With a LS1 automatic, the first and best mod you get is a stall converter. I had one in my old Z and it really woke it up. But what i'm noticing here is that its not so popular a mod in the Mustang world. Is the auto tranny problematic already and a higher stall would just cause more trouble? Other mods planned would be exhaust, intake, pulley and other simple bolt-ons. If you have any suggestions feel free to tell me. :SNSign:

topless98gt · May 23, 2007

That's a really good startup mod list. If I were you, I'd add gears to the list

Just know that they Motive gears are the exact same as the FRPP. I wish I would have known this when I got mine.

The install will run you anywhere from $300 and up. Don't forget to get a new rear-end seal kit while you're at it!

We all look forward to having you as a loyal :SNSign: member! Don't be ashamed of your past...it'll only help your future

AmBo · May 23, 2007

4.10s should be very high on your list

welcome!

Lookin4Stang · May 23, 2007

What gears do the autos come standard with? 273? I would think that the 4.10 would be a bit too much gear in an auto.

Kilgore Trout · May 23, 2007

You should do some studying and learning and listening and searching. Also read this: http://forums.stangnet.com/showthread.php?t=583369

Welcome to StangNet

Lookin4Stang · May 26, 2007

OK I have read quite a bit in the past few days. I don't think my eyes can handle much more. I still can't find a whole lot of info on stall converters though. There were a few write ups on them here and there but if someone could point me in the right direction, i'd be one happy camper. Thanks.

Kilgore Trout · May 26, 2007

Lookin4Stang said:
OK I have read quite a bit in the past few days. I don't think my eyes can handle much more. I still can't find a whole lot of info on stall converters though. There were a few write ups on them here and there but if someone could point me in the right direction, i'd be one happy camper. Thanks.

Ask and ye shall receive sir

http://www.tccoa.com/articles/tranny/index.html

Mustang5L5 · May 26, 2007

Lookin4Stang said:
What gears do the autos come standard with? 273? I would think that the 4.10 would be a bit too much gear in an auto.

If you buy a 99+ Mustang GT, you get 3.27's

4.10's are NOT too much gear for a auto. They are perfect. I know guys who daily drive with 4.30's and 4.56's in their 5-spd's

Lookin4Stang · May 26, 2007

Thanks for the help everyone. The car would be a 99 - 04 GT so I guess 3.27 it is. I had a PI converter in my otherr car and loved it so i'm thinking a 3000 stall would suffice. Couldn't be that loose with a 4.10 mated to it.

topless98gt · May 26, 2007

Kilgore Trout said:
Ask and ye shall receive sir

http://www.tccoa.com/articles/tranny/index.html

Hey Killy, on Mustangs are they called Torque Converters?

Maybe he's looking for a "stall converter" but should be looking for a "torque converter?"

Lookin4Stang · May 26, 2007

topless98gt said:
Hey Killy, on Mustangs are they called Torque Converters?

Maybe he's looking for a "stall converter" but should be looking for a "torque converter?"

Stall converter is just another name for torque converter.

04DarkShadowGT · May 26, 2007

On an auto mustang a stall is a great modification, my auto is slow as balls out of the hole even with a blower. I hate it.

Next mods will be redone trans with 3800 stall and 4.10s.

topless98gt · May 26, 2007

Lookin4Stang said:
Stall converter is just another name for torque converter.

Sweet, I never knew that.

What exactly is a stall converter for anyways?

Lookin4Stang · May 26, 2007

topless98gt said:
Sweet, I never knew that.

What exactly is a stall converter for anyways?

I'm bad with explaining so I cut/paste this from another website.

]

The torque converter converts hydraulic pressure within an automatic transmission to mechanical torque, which drives the drive shafts and, ultimately, the wheels of your car. In design, the torque converter is similar to a turbine engine. Fluid is forced under pressure through small passages called fins. These passages vary in size and flip flop in direction. As fluid is forced through the passages (which get smaller in size) a strong, almost solid “fluid coupling” is created. This is what drives the driveshafts and wheels.

Kilgore Trout · May 27, 2007

The problem with changing out the TC is that it can be very expensive if you are not able to DIY.

Lookin4Stang · May 27, 2007

Kilgore Trout said:
The problem with changing out the TC is that it can be very expensive if you are not able to DIY.

I had a buddy help me out with the install on the 99Z. Dropping the tranny was quite a task as some of the bolts were very hard to get to. We also did a shift kit at the same time but that was a complete disaster.

04DarkShadowGT · May 27, 2007

I was quoted $2500 for a new trans with a 3800 stall capable of handling 1000+whp, trans cooler, and install for everything from www.bc-automotive.com

He did my jmod for $150.

Lookin4Stang · May 28, 2007

04DarkShadowGT said:
I was quoted $2500 for a new trans with a 3800 stall capable of handling 1000+whp, trans cooler, and install for everything from www.bc-automotive.com

He did my jmod for $150.

Have you driven a car with that high a stall before? I know some people that drive a 4200 stall on the street but i'd be weary of driving anything higher than a 3000 for everyday driving unless I had some good $$$ thrown into internals.

007 · May 28, 2007

4.10s and an xcal2 should be your first mods.

Kilgore Trout · May 29, 2007

007 said:
4.10s and an xcal2 should be your first mods.

I disagree...

I think mods should go in this order:
1) shifter
2) quad/fw adjuster
3) new dampers
4) some exhaust stuff
5) new tires
6) gears
7) livewire with custom dyno tune

This starts off cheap and easy and works up to expensive and cannot do without a technician's help.

Noob saying Hi. Many questions also.

New Member

Adhesive Feces

Active Member

New Member

Fried or Broiled ?

New Member

Fried or Broiled ?

That is…until I whipped out my Bissell

New Member

Adhesive Feces

New Member

Member

Adhesive Feces

New Member

Fried or Broiled ?

New Member

Member

New Member

Fried or Broiled ?

Similar threads

Privacy & Transparency

Privacy & Transparency