• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

OPINION WELCOME!

  • Thread starter Thread starter 1980coupe
  • Start date Start date Oct 16, 2007

1980coupe

New Member
Oct 16, 2007
7
0
0
CHICAGO
Oct 16, 2007
#1
  • Oct 16, 2007
  • #1
JUST CONVERTED MY 80 COUPE TO A 5.0 5 SPEED! USE TO BE A STRAIGHT SIX AUTO! I USED A 84 GT AS THE DONOR BUT THE 80 DOES NOT HAVE THE QUAD SHOCK MOUNTS AND THE HOLES IN THE CONTROL ARMS FOR THE SWAY BAR! SHOULD I YANK THE GT CONTROL ARMS OUT AND QUAD SHOCK MOUNTS AND FAB THEM TO THE 80 COUPE? OR CAN CAN I DO WITH OUT THEM AS FAR AS DRAG RACING IS CONCERNED! OH AND YES I USED THE COMPLETE SUBFRAME AND SUSPENTION FROM THE GT AND WHAT A DIFFERENCE I TELL YOU!
 

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Oct 16, 2007
#2
  • Oct 16, 2007
  • #2
first.. turn off your caps lock.

second just swap the entire rear-end. if you do not have the mounts on the body just weld on a big bolt. ive seen it done. and for drag racing no you dont need the sway bar but for everyday driving i recomened it.
 

1980coupe

New Member
Oct 16, 2007
7
0
0
CHICAGO
Oct 16, 2007
#3
  • Oct 16, 2007
  • #3
yes i did use the whole rear end! thanks for the tip on the quad shock tip! and i will drive the car during the summer atleast so i will put the sway bar!
 

PUNISHER RACING

Active Member
Aug 27, 2007
1,124
0
36
FORD CITY, PA.
Oct 17, 2007
#4
  • Oct 17, 2007
  • #4
THROW THE QUAD SHOCKS AWAY......STEP AWAY FROM THE QUADSHOCKS!!!!!!!!!
 

skunk21

Active Member
May 22, 2007
1,203
3
36
Taxachusetts
Oct 17, 2007
#5
  • Oct 17, 2007
  • #5
I fell into the quad shock do it or don't. I searched on here and got some advice and finally took them off and my car was crap w/o them. so I put them back on and now I'm fine. seems like a crap shoot on what mustang will do okay with or without them. I'm not saying punisher is wrong but you might have to do a test with them and w/o. some on here say yes you have to have them and some say no, I did the experiment and my car failed. oh I had just replaced the upper control arms and bushings, and new rear shocks before doing this test.
 

1980coupe

New Member
Oct 16, 2007
7
0
0
CHICAGO
Oct 17, 2007
#6
  • Oct 17, 2007
  • #6
i just took my 80 out today for a test run and it is wheel hop crazy and i cant launch worth a ****! i am going to take the quad shock mounts off my 84 gt donor, however im going to have to weld the quad shock mounts onto the 80 frame! is the 84 gt hatch the same frame demension and length as the 80 coupe or do i have to pretty much eyeball it??? and if i have to eyeball it how much tention is needed on the shock it self from the fram to the rear end???
 
D

Daggar

New Member
Jul 19, 2004
3,902
5
0
Oct 18, 2007
#7
  • Oct 18, 2007
  • #7
Instead of mounting quad shocks and if you have the funds to do it, purchase a set of quality (read MM) lower control arms and replace the uppers with 94+ OEM pieces with some new rubber bushings. If you don't have easy access to a set of 94+ uppers, I believe that MM has those as well.


If you want to get REALLY fancy, toss a panhard bar in there. You could then run any bushing you want in the uppers.
 

rd

Founding Member
Jan 12, 2000
3,316
63
109
Ocean Springs MS
Oct 18, 2007
#8
  • Oct 18, 2007
  • #8
My 82 is also a straight 6 to 5.0 conversion.

I still have a 7.5 in non quadshock axle in there, and have used an 8.8 in it for a couple runs.

I used the 1982 control arms and boxed them. Stock rubber bushings and all.

Still wheelhopped, so I put on my old set (1985) of Lakewood traction bars, and it cured it. It will pull high 1.80 sixty foots on Drag Radials this way.

I would not bother with the quad shocks.
 
D

Daggar

New Member
Jul 19, 2004
3,902
5
0
Oct 18, 2007
#9
  • Oct 18, 2007
  • #9
Yeah... it's pretty tough to NOT have wheel hop with rubber bushings in the lowers with no quads. There's just too much play in the rubber bushings and its compunded by the flex in the OEM control arms.
 

ninety15.0

New Member
Mar 10, 2004
1,336
0
0
Oct 18, 2007
#10
  • Oct 18, 2007
  • #10
Yup i agree with daggar. with flimsy stock control arms and rubber bushings its going to be next to impossible to eliminate wheel hop without the quads in there.

If i were you i would toss some maximum motorsports lower control arms in there for a couple hundred bucks. Weld a bolt onto the chassis for the quadshocks...and box the stock uppers and put new bushings in. You would see a world of difference.
 

1980coupe

New Member
Oct 16, 2007
7
0
0
CHICAGO
Oct 18, 2007
#11
  • Oct 18, 2007
  • #11
thanks for all the opinions out there but i think im going take the quad shock mounts off my 84 gt and use the quad set up on my 80 for right now! im planning on tubbing the car next year putting a narrowed 9" with ladder bars! i want to build a 351w for it but my buddy keeps saying lets go with a 460 but i dont know i think 460 is alot of motor to work with not to mention the tight space in the engine bay!!! what do you guys think???
 
You must log in or register to reply here.

Similar threads

Suspension Harsh Ride
  • PonyGTrider
  • Mar 20, 2026
  • Fox 5.0 Mustang Tech
  • 2 3 4
Replies
62
Views
3K
Fox 5.0 Mustang Tech Apr 11, 2026
Noobz347
C
SN95 Another Coyote swap list
  • catkiller
  • May 10, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
1
Views
395
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 8, 2026
bjornsn95
B
Cobra Brake Conversion - Spare Wheel/Tire Search
  • AeroCoupe
  • Aug 2, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
516
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 2, 2026
AeroCoupe
B
Where to go from here on my build…
  • B0udreaux
  • Jul 14, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
8
Views
467
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jul 18, 2026
AeroCoupe
Can makes noises when driving poping
  • Creomod
  • Oct 14, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
17
Views
815
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 19, 2025
Creomod
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?