• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Overheating Problems

  • Thread starter Thread starter Strype
  • Start date Start date Sep 4, 2007
  • 1
  • 2
Next
1 of 2 Next Last

Strype

Cuthbert catcher
Founding Member
May 11, 1999
61
34
104
Huntsvegas, AL
Sep 4, 2007
#1
  • Sep 4, 2007
  • #1
Well my 93 notch is still overheating. It has a new radiator, new 180 degree thermostat, full of antifreeze w/ water wetter. Stock fan is back on the car.

Drive for a few miles, come back and sit in driveway, or drive thru, or anywhere idling and it starts overheating. Ran about 211-215 yesterday idling after a 15 minute run. I had the a/c on. I turned the a/c off and it dropped just below 210 which IMO is still too hot for this car. It stayed there afterward.

As some of you may remember I had a Taurus fan on it which worked decently but not perfect- car was running 205 and with that fan should have ran 180-190, but the fan had constant issues. So I switched to a flex fan and it started overheating again, so I switched back to the stock fan and it still overheats (210+).

The only thing that has been suggested so far is to change the water pump. Anything I might be missing? The car has an underdrive pulley on the crank.

Thanks,

Jon
 

RYC CUKR

Founding Member
May 19, 2002
1,437
1
38
Orlando
Sep 4, 2007
#2
  • Sep 4, 2007
  • #2
I know you said that you have a new radiator but did you also put a new radiator cap on? I had all sorts of issues with overheating and boiling over that ended up leading back to a worn out radiator cap. Replaced it and no more probs.
 

Strype

Cuthbert catcher
Founding Member
May 11, 1999
61
34
104
Huntsvegas, AL
Sep 4, 2007
#3
  • Sep 4, 2007
  • #3
RYC CUKR said:
I know you said that you have a new radiator but did you also put a new radiator cap on? I had all sorts of issues with overheating and boiling over that ended up leading back to a worn out radiator cap. Replaced it and no more probs.
Click to expand...

Yep it's new
 

SVT32VDOHC

waiting for the next hack atta
Founding Member
Nov 22, 2001
3,501
28
119
Motor City
Sep 4, 2007
#4
  • Sep 4, 2007
  • #4
I vote for a new water pump. I have had 3 foxes...92K, 145K, and 135K. When I got them, I put on new water pump, 180*, new hoses, had the radiator flushed, and new antifreeze...(green stuff) Stock fan blade and clutch. I have never had a problem with overheating while on the street, track freeway, long trips...etc. I bought a replacement at Murrays/Autozone...1yr warrenty 26.99!!! They come with the gasket and they look great in silver.
 

Flavadave4

Active Member
Nov 28, 2003
1,044
21
49
Utica, NY
Sep 4, 2007
#5
  • Sep 4, 2007
  • #5
SVT32VDOHC said:
I vote for a new water pump. I have had 3 foxes...92K, 145K, and 135K. When I got them, I put on new water pump, 180*, new hoses, had the radiator flushed, and new antifreeze...(green stuff) Stock fan blade and clutch. I have never had a problem with overheating while on the street, track freeway, long trips...etc. I bought a replacement at Murrays/Autozone...1yr warrenty 26.99!!! They come with the gasket and they look great in silver.
Click to expand...


Good advise right there
 

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Sep 4, 2007
#6
  • Sep 4, 2007
  • #6
the water journals in the engine could be corodded (sp) and closed up. this is kinda far out but i have known it to happen with people who drive there stangs occasionally. what happened to my buddies car was he would drive it one day let water circulate good then park it for a few weeks. and after doing that so much his journals sordoff rusted up restricting flow. but deff check the pump first.
 

Strype

Cuthbert catcher
Founding Member
May 11, 1999
61
34
104
Huntsvegas, AL
Sep 4, 2007
#7
  • Sep 4, 2007
  • #7
SVT32VDOHC said:
I vote for a new water pump. I have had 3 foxes...92K, 145K, and 135K. When I got them, I put on new water pump, 180*, new hoses, had the radiator flushed, and new antifreeze...(green stuff) Stock fan blade and clutch. I have never had a problem with overheating while on the street, track freeway, long trips...etc. I bought a replacement at Murrays/Autozone...1yr warrenty 26.99!!! They come with the gasket and they look great in silver.
Click to expand...

I'm so doing that this weekend come heck or high water... If that doesn't fix it she's going back where she came from and I'm buying a WRX.

BK_CAULEY said:
the water journals in the engine could be corodded (sp) and closed up. this is kinda far out but i have known it to happen with people who drive there stangs occasionally. what happened to my buddies car was he would drive it one day let water circulate good then park it for a few weeks. and after doing that so much his journals sordoff rusted up restricting flow. but deff check the pump first.
Click to expand...

Hmmmmm that's what I do
 

SVT32VDOHC

waiting for the next hack atta
Founding Member
Nov 22, 2001
3,501
28
119
Motor City
Sep 4, 2007
#8
  • Sep 4, 2007
  • #8
BK_CAULEY said:
the water journals in the engine could be corodded (sp) and closed up. this is kinda far out but i have known it to happen with people who drive there stangs occasionally. what happened to my buddies car was he would drive it one day let water circulate good then park it for a few weeks. and after doing that so much his journals sordoff rusted up restricting flow. but deff check the pump first.
Click to expand...


This is what I was getting at. All 3 of my cars did have some corrosion, that I cleaned up quickly with a wire wheel and lacquer thinner.
 

Strype

Cuthbert catcher
Founding Member
May 11, 1999
61
34
104
Huntsvegas, AL
Sep 4, 2007
#9
  • Sep 4, 2007
  • #9
So do I just need to take the intake off and check those jackets?
 

BK_CAULEY

it's built for speed not longevity, woman
Dec 26, 2006
0
10
49
Thomasville, ga
Sep 4, 2007
#10
  • Sep 4, 2007
  • #10
Strype said:
So do I just need to take the intake off and check those jackets?
Click to expand...

thats a starting point but his cars jackets where corroded in the block and he had to have them rodded out.
 

Strype

Cuthbert catcher
Founding Member
May 11, 1999
61
34
104
Huntsvegas, AL
Sep 4, 2007
#11
  • Sep 4, 2007
  • #11
BK_CAULEY said:
thats a starting point but his cars jackets where corroded in the block and he had to have them rodded out.
Click to expand...

i'll be damned... I'm really beginning to hate this car.
 

85ragtop

BTW, I like dudes.
10 Year Member
Nov 29, 1999
823
475
123
NC
Sep 4, 2007
#12
  • Sep 4, 2007
  • #12
I have nothing new to add, those guys hit the nail on the head.
 

SVT32VDOHC

waiting for the next hack atta
Founding Member
Nov 22, 2001
3,501
28
119
Motor City
Sep 4, 2007
#13
  • Sep 4, 2007
  • #13
Strype said:
So do I just need to take the intake off and check those jackets?
Click to expand...

There are jackets in the intake, but before you go making hours of work for yourself, I would just pull the water pump, clean the front of the timing cover behind it..(I have always found nasty corrosion on the surface of the cover and in the two jackets where water enters and exits) Button that up and see how the car runs. If overheating continues then go ahead and pull the intake and clean the jackets. (however....two of the three cars I mentioned....I did the cooling stuff....then drove them to find an oil leak. I pulled the intakes, replaced the gaskets, and found no corrosion in there....but every car is different.
 
D

Djstorm100

Member
Aug 5, 2007
109
0
16
Sep 4, 2007
#14
  • Sep 4, 2007
  • #14
so if there is corrison in the block, how do you get it out?
 

Strype

Cuthbert catcher
Founding Member
May 11, 1999
61
34
104
Huntsvegas, AL
Sep 4, 2007
#15
  • Sep 4, 2007
  • #15
Djstorm100 said:
so if there is corrison in the block, how do you get it out?
Click to expand...

Pop all the freeze plugs and wash it clean... But I've been thru that on another car and you never get it all out.

If it comes to that point I'll either buy another block or sell the car.
 

302RollinHard

New Member
Sep 26, 2005
0
0
0
Columbus, OH
Sep 4, 2007
#16
  • Sep 4, 2007
  • #16
Don't they make engine coolant flush for corrosion, etc (I think lube shops offer this as a service)??? I know this is redundant, but are you sure you got every air bubble out with the thermostat and radiator changes. I almost sold my car over this type of issue. I used one of those lever vent caps (stant HD) and burped it on a few (3 or 4) occaisions and no more overheating. It don't take much air in the system to make it overheat. Take out the coolant temperature sender and make sure you have coolant there. Also is the spring in your lower rad. hose??
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Sep 4, 2007
#17
  • Sep 4, 2007
  • #17
If it runs cool enough on the highway or at speed, it still sounds like a fan issue to me.
 

Mr. Rustypwnz

Advanced Member
Jun 1, 2005
1,761
63
69
indianapolis/ valdosta ga
Sep 4, 2007
#18
  • Sep 4, 2007
  • #18
make sure you dont have the t-stat in backwards, I f'ed up a while ago and put a 180 in backwards and it ran 215 all day long!!!
 

SVT32VDOHC

waiting for the next hack atta
Founding Member
Nov 22, 2001
3,501
28
119
Motor City
Sep 5, 2007
#19
  • Sep 5, 2007
  • #19
Well, if the problem persists....take is to a radiator shop. A local shop flushed out two of my Honda CR250 radiators on my dirtbike. They were clogged, they were 200 bucks EACH new. He flushed them with this acid and then flushed them again with coolant/water for 40 bucks. They were like brand new. He told me I should have seen the CRAP that came out. My bike has no more overheating problems. He also informed me that he can do that to any car radiator, or motor block.
 

Strype

Cuthbert catcher
Founding Member
May 11, 1999
61
34
104
Huntsvegas, AL
Sep 5, 2007
#20
  • Sep 5, 2007
  • #20
302RollinHard said:
Don't they make engine coolant flush for corrosion, etc (I think lube shops offer this as a service)??? I know this is redundant, but are you sure you got every air bubble out with the thermostat and radiator changes. I almost sold my car over this type of issue. I used one of those lever vent caps (stant HD) and burped it on a few (3 or 4) occaisions and no more overheating. It don't take much air in the system to make it overheat. Take out the coolant temperature sender and make sure you have coolant there. Also is the spring in your lower rad. hose??
Click to expand...

I'll buy a vent cap this weekend, I tried to burp it but it may not have gotten all out- worth a shot


Spring? I haven't seen one

HISSIN50 said:
If it runs cool enough on the highway or at speed, it still sounds like a fan issue to me.
Click to expand...

You maybe right... It acted fine with the e-fan on but the e-fan kept trying to catch fire

Maybe it needs a new fan clutch?

slow95gt said:
make sure you dont have the t-stat in backwards, I f'ed up a while ago and put a 180 in backwards and it ran 215 all day long!!!
Click to expand...

I put it back in the way it came out- I may have to open it back up and check. Which way does the pointy end go?

SVT32VDOHC said:
Well, if the problem persists....take is to a radiator shop. A local shop flushed out two of my Honda CR250 radiators on my dirtbike. They were clogged, they were 200 bucks EACH new. He flushed them with this acid and then flushed them again with coolant/water for 40 bucks. They were like brand new. He told me I should have seen the CRAP that came out. My bike has no more overheating problems. He also informed me that he can do that to any car radiator, or motor block.
Click to expand...

I might have to try that if all else fails.
 
  • 1
  • 2
Next
1 of 2 Next Last
You must log in or register to reply here.

Similar threads

Engine 1986 GT Overheating issues
  • 86 5O GT
  • Jan 25, 2026
  • Fox 5.0 Mustang Tech
Replies
18
Views
960
Fox 5.0 Mustang Tech Jan 29, 2026
86 5O GT
M
Resolved 1988 Foxbody - Overheating Summer
  • MDrisc
  • Oct 26, 2025
  • Fox 5.0 Mustang Tech
Replies
16
Views
1K
Fox 5.0 Mustang Tech Jul 17, 2026
fasterthangas
F
M
1997 Mustang GT Overheating Issue
  • Mustang1988!!
  • Sep 3, 2025
  • SN95 4.6L Mustang Tech
Replies
5
Views
422
SN95 4.6L Mustang Tech Sep 24, 2025
squeak93
L
Engine 85 GT Excessive Idle
  • lutzkecj
  • Sep 18, 2026
  • Fox 5.0 Mustang Tech
Replies
5
Views
372
Fox 5.0 Mustang Tech Sep 21, 2026
86HO5.0
8
F
Overheating after ECU flash
  • fourtyfour338
  • Jul 23, 2025
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
1
Views
158
1996 - 2004 SN95 Mustang -General/Talk- Jul 23, 2025
Noobz347
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?