• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Ped. mount rocker arm issues

  • Thread starter Thread starter JenkinsBS
  • Start date Start date Jun 19, 2007

JenkinsBS

Founding Member
Apr 16, 2002
1,001
1
39
Washington
Jun 19, 2007
#1
  • Jun 19, 2007
  • #1
Im installing my rocker arms back onto my car (same ones that were on there a year ago), and am running into a few issue...

Im following cranes instructions (http://www.cranecams.com/pdf/453e.pdf) on how to make sure there properly adjusted, and im having a hard time finding what stroke is the compression stroke. It says

"When both pushrods are at their lowest point and appear to be at an equal height, you are in the correct position to install the cylinder's rocker arms. This will occur when the cylinder is at top-dead-center, on its compression stroke."

now is it refering to when the pushrods are both at rest, and not moving at all when you turn the motor over by hand... or when the pushrod is coming down and the other starts to move up, they hit the same height?

Also, my motor has been sitting for quite some time now, w no oil in it, just freshly rebuilt. It has the assembly grese and thats it. Is it going to matter that the lifters dont have any oil in them? If it does, how do i get them ready for install?

Thanks

BJ
 

cenok is family

15 Year Member
Jun 25, 2003
1,409
69
79
Norman, Ok
Jun 19, 2007
#2
  • Jun 19, 2007
  • #2
i just finished what you did yesterday actually. i have crane 1.7 roller rockers on my car. when adjusting them, do one cylinder at a time. turn the crank over so that both the lifters for whatever cylinder you are doing are at their lowest point. then start tightening down the rocker arm until you see the lifter (for lack of a better term) collapse. pretty much you want to take all the slack out of the pushrod. then with a torque wrench set at 18-20 lbs turn it until it clicks. if it takes more than one full rotation of your torque wrench for the rocker to be completely torqued, then you need to shim it. thats the way i did it so i hope it's right lol. i just started my motor for the first time yesterday and it seems correct so far. also, if you still can, soak your lifters in oil as well as fill your pushrods with oil. i didn't do either because by the time i realized i was supposed to, my motor was already back together so i just filled up on all fluids, packed the oil pump with petrolium grease to create a vacuum and started it up. like i said it seems fine so far. i looked down my oil filler tube on my valve cover and my rockers are getting oil. good luck!
 

JenkinsBS

Founding Member
Apr 16, 2002
1,001
1
39
Washington
Jun 21, 2007
#3
  • Jun 21, 2007
  • #3
cenok is family said:
i just finished what you did yesterday actually. i have crane 1.7 roller rockers on my car. when adjusting them, do one cylinder at a time. turn the crank over so that both the lifters for whatever cylinder you are doing are at their lowest point. then start tightening down the rocker arm until you see the lifter (for lack of a better term) collapse. pretty much you want to take all the slack out of the pushrod. then with a torque wrench set at 18-20 lbs turn it until it clicks. if it takes more than one full rotation of your torque wrench for the rocker to be completely torqued, then you need to shim it. thats the way i did it so i hope it's right lol. i just started my motor for the first time yesterday and it seems correct so far. also, if you still can, soak your lifters in oil as well as fill your pushrods with oil. i didn't do either because by the time i realized i was supposed to, my motor was already back together so i just filled up on all fluids, packed the oil pump with petrolium grease to create a vacuum and started it up. like i said it seems fine so far. i looked down my oil filler tube on my valve cover and my rockers are getting oil. good luck!
Click to expand...


Yea, im at the point right now where the engine is back together, heads and lower intake are all torqued and gasketed up, i really wouldnt enjoy taking them back off. But if i have to, i will

My concern is with the lifters... it seems that on one of my cylenders, the pushrods arent at equal hights when they should be. Could one of the lifters be collapsed and the other not? Now there is a point where they DO equal out, however its when one rod goes all the way down, and another half rotation of the engine starts sending the other one up.

Im afraid that thats not the compression stroke. So what would be the easiest way to find out when the cylender is at TDC on the compression stroke?

And if i happen to tighten down the lifters on the wrong stroke or whatever, what is the worst that could happen?
 

JenkinsBS

Founding Member
Apr 16, 2002
1,001
1
39
Washington
Jun 21, 2007
#4
  • Jun 21, 2007
  • #4
??? bump ???

anyone?
 

90_Red_LX

Member
Sep 29, 2003
668
5
19
Asheboro, NC
Jun 21, 2007
#5
  • Jun 21, 2007
  • #5
Look for the intake rocker arm, watch it's movements. When the intake opens, it's on the intake stroke, as it closes it's on the compression stroke. When that rocker stops moving thats where you want to be. Thats TDC compression stroke. There is a narrow window where both rockers haven't budged, so you need to turn the motor slowly as the intake valve closes, and watch carefully.
 

JenkinsBS

Founding Member
Apr 16, 2002
1,001
1
39
Washington
Jun 22, 2007
#6
  • Jun 22, 2007
  • #6
Roger that.

Also, what about the issue of the lifters not being primed and what not? Could one of them be collapsed and one of them not? Theyve been sitting in the motor for 3 or so years...
 

302RollinHard

New Member
Sep 26, 2005
0
0
0
Columbus, OH
Jun 22, 2007
#7
  • Jun 22, 2007
  • #7
all you need to do is prime the oil system with a priming tool and drill (runnung in reverse) before you start up the engine.
 

JenkinsBS

Founding Member
Apr 16, 2002
1,001
1
39
Washington
Jun 27, 2007
#8
  • Jun 27, 2007
  • #8
90_Red_LX said:
Look for the intake rocker arm, watch it's movements. When the intake opens, it's on the intake stroke, as it closes it's on the compression stroke. When that rocker stops moving thats where you want to be. Thats TDC compression stroke. There is a narrow window where both rockers haven't budged, so you need to turn the motor slowly as the intake valve closes, and watch carefully.
Click to expand...

Okay, so when doing this, after the intake valve fully closes, should the pushrods be at equal height?

In the Crane Cams manual, it says, "When both pushrods are at their lowest
point and appear to be at an equal height, you are in the correct position to install the cylinder's rocker arms. This will occur when the cylinder is at top-dead-center, on its compression stroke"

What if the pushrods arent at equal height when the intake valve closes?
 

90_Red_LX

Member
Sep 29, 2003
668
5
19
Asheboro, NC
Jun 27, 2007
#9
  • Jun 27, 2007
  • #9
JenkinsBS said:
Okay, so when doing this, after the intake valve fully closes, should the pushrods be at equal height?

In the Crane Cams manual, it says, "When both pushrods are at their lowest
point and appear to be at an equal height, you are in the correct position to install the cylinder's rocker arms. This will occur when the cylinder is at top-dead-center, on its compression stroke"

What if the pushrods arent at equal height when the intake valve closes?
Click to expand...


How far off are they? If there damn close then it should be good enough, I wouldn't think it would have to be TDC plus or minus a tenth of a degree. If there more than just barely off, look at the lifters on those pushrods, ones probably collapsed and pushed down. If neither one is collapsed, then your pushrods are not the same length. Only things I can think of.

If the lifters are collapsed, buy a quart of oil, and let em soak overnight in it. Pour half in a cup, toss 8 or so of em int here, then the cut the top of the quart off and let it soak in that or use another cup.
 

JenkinsBS

Founding Member
Apr 16, 2002
1,001
1
39
Washington
Jun 28, 2007
#10
  • Jun 28, 2007
  • #10
90_Red_LX said:
How far off are they? If there damn close then it should be good enough, I wouldn't think it would have to be TDC plus or minus a tenth of a degree. If there more than just barely off, look at the lifters on those pushrods, ones probably collapsed and pushed down. If neither one is collapsed, then your pushrods are not the same length. Only things I can think of.

If the lifters are collapsed, buy a quart of oil, and let em soak overnight in it. Pour half in a cup, toss 8 or so of em int here, then the cut the top of the quart off and let it soak in that or use another cup.
Click to expand...


Yea, they are baaaarely off. I was thinking the same thing with one of the lifters may be collapsed.

So im like Cenok is Family at this point. The motors all together and ready to go, i really dont want to tear down back to that point to where i can remove the lifters.

Would it be bad if i proceded to tighten down the rockers with the proper procedure, then prime the motor before start up. That should un collapse the lifters, eh?
 

cenok is family

15 Year Member
Jun 25, 2003
1,409
69
79
Norman, Ok
Jun 28, 2007
#11
  • Jun 28, 2007
  • #11
JenkinsBS said:
Yea, they are baaaarely off. I was thinking the same thing with one of the lifters may be collapsed.

So im like Cenok is Family at this point. The motors all together and ready to go, i really dont want to tear down back to that point to where i can remove the lifters.

Would it be bad if i proceded to tighten down the rockers with the proper procedure, then prime the motor before start up. That should un collapse the lifters, eh?
Click to expand...

that's what i did and my motor is getting oil fine, oil pressure is at like 55 when cruising.
 

JenkinsBS

Founding Member
Apr 16, 2002
1,001
1
39
Washington
Jun 28, 2007
#12
  • Jun 28, 2007
  • #12
Thats what im going to do than... hopefully everything works out okay.

Im also worried about the surface rust thats on my flywheel.

Becasue its been sitting for so long, the flywheel has built up a good ammount of rust on it, and im afraid that its going to cause the clutch to slip. Either that or the clutch is going to grind off all the rust and everything will be okay...

Thanks for the help guys

Brian
 

cenok is family

15 Year Member
Jun 25, 2003
1,409
69
79
Norman, Ok
Jun 30, 2007
#13
  • Jun 30, 2007
  • #13
JenkinsBS said:
Thats what im going to do than... hopefully everything works out okay.

Im also worried about the surface rust thats on my flywheel.

Becasue its been sitting for so long, the flywheel has built up a good ammount of rust on it, and im afraid that its going to cause the clutch to slip. Either that or the clutch is going to grind off all the rust and everything will be okay...

Thanks for the help guys

Brian
Click to expand...

as long as its just surface rust the clutch will just grind it off
 
You must log in or register to reply here.

Similar threads

H
Ongoing Battle With Hydraulic Lifters
  • hailer06
  • Jun 8, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
617
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 9, 2026
Noobz347
6
Hey all,I’m putting together a 302 for my 1968 Mustang and wanted to post the combo + some questions to make sure I’m not missing crucial
  • 68_Disgustang
  • Feb 22, 2026
  • 1965 - 1973 Classic Mustangs -General/Talk-
Replies
5
Views
1K
1965 - 1973 Classic Mustangs -General/Talk- Oct 19, 2026
mattcrp1
M
Tightening upper control arm bushings at ride height dilemma… need some help
  • AnthonyA1234
  • Dec 27, 2024
  • Fox 5.0 Mustang Tech
  • 2 3
Replies
51
Views
7K
Fox 5.0 Mustang Tech Feb 27, 2025
General karthief
Engine Roller Rocker to Valve Retainer Interference - Possible Source of Valve Train Noise
  • AeroCoupe
  • May 22, 2023
  • Fox 5.0 Mustang Tech
Replies
11
Views
2K
Fox 5.0 Mustang Tech May 28, 2023
AeroCoupe
E
Finished my Fox Hydroboost Install - Tips
  • Engineer Duane
  • Apr 9, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
4
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- May 5, 2025
Engineer Duane
E
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?