PIC REQUEST: FOX TB Swapped SN-95's

Adam95GT · Mar 23, 2009

Just want to see where everything lines up at.... I found a guy switching to carb $200 for everything i need 70mm bbk tb and egr.... i also found a 65mm tb and egr as well as iac and egr valve for $100 but would still need the cable and bracket... both seem like a good deal...

I am basically trying to see where everything sits and different CAI set ups... im considering cutting a hole out of my new shaved bay to hide the maf and filter in... and runing a 90* elbow with a strait pipe into the fender...

turbogt · Mar 23, 2009

I approve this thread

95strokerPSU · Mar 23, 2009

Best pic I have...

lazy_stang · Mar 23, 2009

WOW
thats a nice F'n clean lookin engine bay. . . WOW

Adam95GT · Mar 23, 2009

except for them ac lines on the fire wall... LOL

Where you get that elbow from

Black Stampede · Mar 23, 2009

fastgtfairlane · Mar 24, 2009

i redrilled the holes on my upper plenum and reused my sn95 tb. i had some 1/8th inch aluminum sheets laying around that i used to make a plate to cover the egr passage and made a bracket for the throttle linkage.

99FiveOh · Mar 24, 2009

Dave, your car is beautiful! I think you just made up my mind as to the color scheme for my car, blue and silver!

No cold air intake on my previous car, but it shows the possibilities with a supercharger and Fox TB setup:

RIO5.0 · Mar 24, 2009

Oil fill vent & IAT sensor in tubing..

straight shot to fender... 3.5 exh tubing with a Scotch pad scuff..

96darkhorse · Mar 24, 2009

fastgtfairlane said:
i redrilled the holes on my upper plenum and reused my sn95 tb. i had some 1/8th inch aluminum sheets laying around that i used to make a plate to cover the egr passage and made a bracket for the throttle linkage.

did you feel a difference going with that setup powerwise?....looks easy to do...only things to do for it is like you stated...or did you just do it for the looks ?

fastgtfairlane · Mar 25, 2009

it was not the easiest mod to do. it took all day to do with having to make the plate to go between the tb and manifold. i had simple tools that took forever but im sure with some better fabricating tools you could do it much quicker. i used a cutoff wheel and an angle grinder to do it. and i had a drill. i had to line up the tb to the inlet hole, then redrill everything making sure it would match up. then made my own cai. i had to make the throttle linkage as well. for a small fee i will make the necessary parts to make the swap. you will have to drill out the holes on the manifold. i did it cause i put the fox valve covers on and with the elbow i couldnt get the tb off without taking the plenum off. plus its cleaner and runs a lil better

nmcgrawj · Mar 26, 2009

Black Stampede said:

You got any more pics of your turbo install?

deftsound · Mar 26, 2009

Are there any advantages to going to the fox tb? HP gains?

Black Stampede · Mar 26, 2009

nmcgrawj said:
You got any more pics of your turbo install?

Yeah I have some, but they are on my buddies computer. All the ones I have are after it was completed. I'll see what I can get up here.

Hef5.0weisen · Mar 27, 2009

deftsound said:
Are there any advantages to going to the fox tb? HP gains?

Man oh man...you're opening a can of worms with that question....:stirpot:

big 'ol debate over that, Killercanary did a comparo, but used different size TB's before and after, turned into like a 4 page thread, some of the responses were entertaining.... :fairyfight:

I think it looks better, I'm gathering the parts to do the swap.

Adam95GT · Mar 27, 2009

SCORE! $175 For everything... I think someone is buying my elbow and tb for $175 also

I even got the heater hose lines and the bung for the coolant pasage on the lower intake!

Adam95GT · Mar 27, 2009

Question....

Whats the sensor on the back left corner on the manifold..... as seen here

Also whats the plug for on the right side??? can put the nipple for the coolant line to the egr there??? its the same thread size!!!!

99FiveOh · Mar 27, 2009

did you forget to post up a pic or something? All I see in that pic is the fuel pressure regulator and an injector.

GT_green_GT · Mar 27, 2009

Its there. The square pipe style plug. as long as it doesnt go in to a coolant chamber or into a single intake runner id say it might work. its gonna be a pain in the a** to route to there.

Adam95GT · Mar 27, 2009

GT_green_GT said:
Its there. The square pipe style plug. as long as it doesnt go in to a coolant chamber or into a single intake runner id say it might work. its gonna be a pain in the a** to route to there.

I think its a coolant chamber thats what i want it to be atleast i need the coolant line for the egr spacer... Wont be bad to run... ill figure it out

PIC REQUEST: FOX TB Swapped SN-95's

Adam95GT

New Member

turbogt

Member

95strokerPSU

Member

lazy_stang

New Member

Adam95GT

New Member

Black Stampede

fastgtfairlane

New Member

99FiveOh

RIO5.0

96darkhorse

fastgtfairlane

New Member

nmcgrawj

Advanced Member

deftsound

Please ask me how much my supercharger cost

Black Stampede

Hef5.0weisen

Adam95GT

New Member

Adam95GT

New Member

99FiveOh

GT_green_GT

New Member

Adam95GT

New Member

Similar threads

PIC REQUEST: FOX TB Swapped SN-95's

New Member

Member

Member

New Member

New Member

New Member

New Member

Advanced Member

Please ask me how much my supercharger cost

New Member

New Member

New Member

New Member

Similar threads

Privacy & Transparency

Privacy & Transparency