Project 306

[zkillrr]

Its been a long time coming and I'm finally going to start on my 94gt. I just pick up
a dss 306 short block but had a question about the motor. It has flat top pistons and I bought a Strim almost two years ago and want to install it also. Do you think I can get it tuned for a weekend car until I can get the injectors I need. I will be getting 42s this coming march but wanted to have it tune now with the 24s and fmu. The block I got dss say is good for spray or n/a and wanted to hear what you guys think about boost 9#s on it. The vortech is going on just wanted some advice,thanks

 

[nmcgrawj]

Its been a long time coming and I'm finally going to start on my 94gt. I just pick up
a dss 306 short block but had a question about the motor. It has flat top pistons and I bought a Strim almost two years ago and want to install it also. Do you think I can get it tuned for a weekend car until I can get the injectors I need. I will be getting 42s this coming march but wanted to have it tune now with the 24s and fmu. The block I got dss say is good for spray or n/a and wanted to hear what you guys think about boost 9#s on it. The vortech is going on just wanted some advice,thanks

March is in 12 days.....When do you plan on having the new block/motor in the car?

From what i've read from others.....no one likes a FMU. If you are having someone tune it....you'll be paying twice to have it done for the 42s.


Wait 2 weeks, or more, get the 42s....and get it tuned once. Do it right the first time. It'll take some patience but if you attempt to do 24s and a FMU....and its nothing but headaches, you might as well just play it safe and wait

 

[zkillrr]

I'm going to start on it wed day, but i'm waiting on a friend to complete his car to get the 42s. He told me it may be finish in march.

 

[94-302-vert]

Run it without the blower to break in the motor and be safe with the 24's for now... THEN add teh blower and 42's and get it tuned all at once...

Is it really worth not breaking the motor in right or burning it up to have more ponies a few weeks earlier?

 

[ProKiller]

what cam is in it?

 

[zkillrr]

what cam is in it?

Holley systemax heads 1.94/1.60 and.508/.509 lift 224/226 dur holley cam.

 

[Pokageek]

I dont know how yo uwill run that blower with flat tops..too much compression.

 

[zkillrr]

I dont know how yo uwill run that blower with flat tops..too much compression.

I wanted some advice on this motor, i have heard of differ people with high compression motors and running under 10#s I would be running 8 to9#s.

 

[ProKiller]

Holley systemax heads 1.94/1.60 and.508/.509 lift 224/226 dur holley cam.

whats the lobe separation? its not the worst cam for a blower setup but it's not really designed for it by looking at the numbers.

if the compression is only 8-9#s you'll be fine with the blower.

 

[fasterthanthem]

I have the same shortblock as him, I believe with his heads compression is actually close to 10:1.

 

[zkillrr]

I will be ok for boost the motor is a 9:7.1 compression, What do you all think about me putting in the 42s with calbr mass air and PMS tune?

 

[thethirdeye88]

thats alot of compression for boost...im gonna be running 10 - 11.1 not sure yet, i get it put together in a couple of weeks...i was thinking about a weind 174 blower on it, but my mechanic said no...

 

[zkillrr]

I talked to a guy today that is running a 10:5.1 on his with a 10# pulley and he is fine so mine is lower in compression and boost. I will only be running 8 to 9 pounds.