• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Rear End Grind

  • Thread starter Thread starter dirty slut
  • Start date Start date Feb 12, 2006
D

dirty slut

New Member
Nov 12, 2005
59
0
0
Feb 12, 2006
#1
  • Feb 12, 2006
  • #1
My rear end is grinding, at first I thought it was nothing but now it is doing it worse, started doing it really bad 2day. At first it would grind a little when starting out from a dead stop as I released the clutch. Now it does it for a second when im going around a corner at slow speeds. It sounds bad and makes the car kind of shake and the passanger in the back seat said they felt something grinding right under their butt.

I was gonna try to check the rear axle/differential fluid tommorrow, and change it if it is low, anyone have any ideas what may be going on???
 

HardmanGT

Founding Member
Oct 5, 2001
500
0
17
Thomaston, CT
Feb 12, 2006
#2
  • Feb 12, 2006
  • #2
check to see if anything is rubbing on the driveshaft, too
 
D

dirty slut

New Member
Nov 12, 2005
59
0
0
Feb 12, 2006
#3
  • Feb 12, 2006
  • #3
ok will do, any other ideas of what this may be?
 

bill302

Active Member
Nov 2, 2005
2,131
1
46
alabama,gadsden
Feb 12, 2006
#4
  • Feb 12, 2006
  • #4
my best guess would be fluid low and your checking that tommorrow check rear end for leaks and replace gaskets leaking and look at back tires while under car and see if the inside tire walls under car are wet or show signs of axle/wheel seals leaking usually if axle/wheel seal is leaking tire wall will show signs... good luck. also besure to add friction modifier..
 

bill302

Active Member
Nov 2, 2005
2,131
1
46
alabama,gadsden
Feb 12, 2006
#5
  • Feb 12, 2006
  • #5
inspect fluid for any metal shavings or foriegn materials closely and you will want to turn driveshaft by hand with car in neutral before adding fluid to ensure smooth action checking for bad bearings by feeling for any binding and listening you mighty need an assistant during this check. besure to chock wheels and use car stands and blocks for safety.
 
V

v8only

Active Member
Jul 3, 2003
2,378
22
49
Feb 13, 2006
#6
  • Feb 13, 2006
  • #6
more than likely it's the wheel bearings in the rear, though it certainly could be internal issues too.

in my experience, i've seen the rear wheel bearings fail almost religiously between 160-190k miles.
 
D

dirty slut

New Member
Nov 12, 2005
59
0
0
Feb 13, 2006
#7
  • Feb 13, 2006
  • #7
Well I didnt get to get it on the lift today b/c the hobby shop was closed. I think im gonna go get a new gasket, gear oil, and RTV and just replace it tommorow anyways.
 

bill302

Active Member
Nov 2, 2005
2,131
1
46
alabama,gadsden
Feb 13, 2006
#8
  • Feb 13, 2006
  • #8
ensure you check all bearings as i stated above and you might want to remove axles and inspect axle bearings they are bad about going bad and cut into axles and cause grinding if this is the case a factory replacement bearing wont work but you can use an OPTIONAL: AXLE REPAIR PACKAGE BEARING AXLE REPAIR BEARING ALLOWS BEARING & SEAL TO RIDE ON UN-WORN AXLE PATH.these special bearings can be purchased at any car parts store. goodluck...
 

Dagz

New Member
Dec 2, 2005
173
0
0
Quesnel Canada
Feb 13, 2006
#9
  • Feb 13, 2006
  • #9
clutch pacs will stick together if there is no friction modifier, seen it a million in one times, if you are gunna tear it down don't forget to add it!!!!!
 
D

dirty slut

New Member
Nov 12, 2005
59
0
0
Feb 13, 2006
#10
  • Feb 13, 2006
  • #10
will do, i just went and bought 3 quarts of Mobil1 synthetic gear oil, then some Friction Modifier stuff, some Ultra Black RTV, and a Felpro Gasket
 
D

dirty slut

New Member
Nov 12, 2005
59
0
0
Feb 14, 2006
#11
  • Feb 14, 2006
  • #11
Well I changed the fluid today. I had a mechanic take a look at the gears once I got the girdle off, and all the gears look good and there were no metal shavings. He also said my Universal Joints and Spider gears looked fine. There was no play in the driveshaft either.

I took it for a little drive and it didnt grind but it still bucks like a bronco. I have changed the motor/tranny mounts, and changed the tranny fluid. The car jerks back and forth really bad, usually when im in 5th and I slow down till about 45, then try to give it a little gas, it starts jerking forwards and backwards really bad, anyone know whats going on?
 
You must log in or register to reply here.

Similar threads

T
Drivetrain TREMEC TKX 1–2 Grinding Issue at ~4,000 Miles + Poor Warranty/Customer Service Experience
  • Ttopfoxguy
  • Oct 10, 2026
  • Fox 5.0 Mustang Tech
Replies
5
Views
328
Fox 5.0 Mustang Tech Oct 15, 2026
JMG9350
J
S
Drivetrain Downshifting from 3rd to 2nd issue
  • Scott_S
  • Apr 23, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
35
Views
1K
Fox 5.0 Mustang Tech Oct 12, 2026
limp
Clicking sound from driveshaft/rear differential
  • matthewt
  • Aug 27, 2026
  • 2015 - 2023 (S550) Mustang -General/Talk
Replies
2
Views
199
2015 - 2023 (S550) Mustang -General/Talk Aug 28, 2026
matthewt
B
Electrical Why does my fox body keep frying eecs
  • brandyn200
  • Jun 20, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
526
Fox 5.0 Mustang Tech Jun 25, 2026
AeroCoupe
Drivetrain Rear end clunk
  • seanmahoney
  • Oct 13, 2025
  • SN95 4.6L Mustang Tech
Replies
3
Views
525
SN95 4.6L Mustang Tech Oct 13, 2025
nickyb
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?