• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-

Rear wheels bind up

  • Thread starter Thread starter Whitehorse88
  • Start date Start date Apr 3, 2018
W

Whitehorse88

New Member
Apr 3, 2018
24
1
3
Apr 3, 2018
#1
  • Apr 3, 2018
  • #1
Back story is I just purchased an 88 coupe. I in the middle of going through the car and see what’s been done to it and also neglected. I was checking the rear end. I had the car in neutral with e brake off. Started rotating the tires. Got about 3/4 the way through a full rotation when it suddenly stopped. Checked for drive shaft catching on something, it wasn’t. During my shake down run with the car, I felt clunking at low speeds when making a left turn. But it doesn’t do every time. My thinking is something with the rear diff or axles. Does anyone have any insight before I blow this rear end apart?
 

RangerJoe

I leave the horn on while driving
15 Year Member
Apr 26, 2010
2,560
1,146
184
Georgia
Apr 3, 2018
#2
  • Apr 3, 2018
  • #2
Possibly a ring gear bolt backing out or something hitting the driveshaft or pinion flange.

Joe
 
W

Whitehorse88

New Member
Apr 3, 2018
24
1
3
Apr 3, 2018
#3
  • Apr 3, 2018
  • #3
Ok. I’m stupid. When I had the rear of the car on jack stands, I didn’t raise my pinion angle to normal ride height. My bad. That fixed the binding but I still have this rapid clunking, for lack of a better term. I was able to duplicate, somewhat, while the car was on stands in first gear. When it was on the road, it would only do it when I turn left and it was much more noticeable. And it’s not all left turns. I also noticed a squeak when the tires were rotating at a decent rpm. I’ve checked for slack in the drive shaft....nothing. Not sure if the 2 are related. Any suggestions outside of rebuilding the rear? This is where I think my issue is
 

General karthief

wonder how much it would cost to ship you a pair
Mod Dude
Aug 25, 2016
28,128
10,748
213
polk county florida
Apr 3, 2018
#4
  • Apr 3, 2018
  • #4
If this is a V8 car it will have a traction lock type differential, if it has a lot of miles on it pop the rear cover off draining and clean the inside with brake cleaner then use black rtv and install the cover, add gear oil with some friction modifier the find a parking lot and do slow figure 8's, about 6 or 8 should work, that may take care of the noise. While your under there check your control arm bushings for damage or ware.
 
You must log in or register to reply here.

Similar threads

Drivetrain Rear end clunk
  • seanmahoney
  • Oct 13, 2025
  • SN95 4.6L Mustang Tech
Replies
3
Views
523
SN95 4.6L Mustang Tech Oct 13, 2025
nickyb
Drive Shaft/Rear Diff Issue on 2014 GT
  • DudeStang
  • Jun 16, 2025
  • 2010 - 2014 Specific Tech
Replies
11
Views
2K
2010 - 2014 Specific Tech Jan 21, 2026
gkomo
S
Look at my rear end!
  • sleeprtsi
  • Aug 4, 2024
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
8
Views
995
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 7, 2024
limp
Mustang II 4 cyl gear hunting and possibly messed up vacuum system
  • oesterreicher
  • May 31, 2026
  • 1974 - 1978 Mustang II Talk & Tech
Replies
11
Views
577
1974 - 1978 Mustang II Talk & Tech Jun 14, 2026
manicmechanic007
O
SOLD FS: 18" FR500 chrome wheels and Toyo tires
  • optionizerSS
  • May 21, 2026
  • Other Classifieds
Replies
1
Views
259
Other Classifieds Jun 2, 2026
optionizerSS
O
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?