• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Rollcage AND Subframe Needed?

  • Thread starter Thread starter WhiteThunder
  • Start date Start date Jan 2, 2008

WhiteThunder

New Member
Oct 16, 2005
52
0
0
Jan 2, 2008
#1
  • Jan 2, 2008
  • #1
As some of you know I'm getting a nice firm plan for how I'm restoring my convertible but I've run into a dilemma. I going to put some form of undercoating on my car and coat the interior while it's stripped. (I never want rust again if I can help it.) I'm going with a cage on the interior because of all the reasons one would need a cage and I had subframes connectors on my list of parts too. Will I need both? I'm having to put new exhaust on it and I'm going to coat the bottom at the same time which would mean subframes would be needed now. Interior will take awhile to get everything together so the cage can hold off for a little while. This isn't going to be some hardcore race car either so I won't need tons of stiffening I just want it to feel a little more solid. What would you guys do?
 
J

Jack's95gt

Member
Aug 15, 2004
443
1
18
Huntingdon Valley, PA
Jan 2, 2008
#2
  • Jan 2, 2008
  • #2
I just picked up 8 point roll bar from http://www.swracecars.com/
They have a bolt in roll bar and a sub frame connector that is bolt in that goes from the k member to the rear control arms.
 

Darkwriter77

Resident Ranting Negative Nancy
5 Year Member
Jul 1, 2005
315
283
134
Apache Junction, AZ
Jan 2, 2008
#3
  • Jan 2, 2008
  • #3
Depends on what kind of times you expect to be running in the future. NHRA mandates a roll bar on 'verts when you're running below a certain E/T ... although I can't recall exactly what time, exactly (13.49, I think). A cage will also help stiffen up the frame significantly, but do keep in mind that they add a bit of weight, as well.

Subframes are a good idea on ANY Fox 'vert, period. I'm planning to put a set on my '86 GT, even though it's a sluggish all-stock slug at the moment - I'm just sick of all of the chassis flex. Subs make the suspension do all of the work, rather than the chassis, itself, so not only will it make your car ride better, but it'll help with cornering and launch, as well.

If you can, get a cage that ties in with your subframes so that they bolt/weld together as a solid unit. Maximum Motorsports has a decent setup, I've read, as well as Wolfe Racecraft - maybe give those a peek.
 

2000xp8

SN Certified Technician
Aug 8, 2003
8,075
1,658
194
NJ
Jan 2, 2008
#4
  • Jan 2, 2008
  • #4
If this car is not going to see a whole lot of sub 13 second runs, i wouldn't do the cage.
They aren't the prettiest in a vert, i'd rather have a light bar which does little to nothing for rigidity.

I'd use the top of the line set of global west subs. And leave it at that.http://www.globalwest.net/mustang%2079-98.htm
 

WhiteThunder

New Member
Oct 16, 2005
52
0
0
Jan 2, 2008
#5
  • Jan 2, 2008
  • #5
Thanks for the thoughts guys. I think I'm going to just go with the subframes and not worry about the bar. Which I didn't realize my mistake earlier I was talking about a roll bar and not a cage. Been sick lately and I've been sorta out of it. I'm not planning on dragging the car or anything...well, maybe a few times. With what I'm at though, HP wise, I don't think I'll be in the 13's. I don't want the car any faster, it has enough balls for a street daily driven car. Thanks again guys.
:SNSign:
 
8

86bluecobra

Advanced Member
Dec 20, 2004
4,265
12
69
B.C. Canada
Jan 2, 2008
#6
  • Jan 2, 2008
  • #6
Sub-frames for sure and a nice roll-bar if you can find one. But personally I would just get the sub-frames and call it a day.
 
You must log in or register to reply here.

Similar threads

B
Subframe connector question
  • B0udreaux
  • Jan 27, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
20
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Feb 5, 2026
rednotch
M
2001 SVT Cobra Decision Time
  • Mec
  • Aug 13, 2026
  • The Welcome Wagon
Replies
5
Views
213
The Welcome Wagon Aug 14, 2026
nickyb
Fox Full set of seats in the back of a hatch
  • keel
  • Aug 28, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
8
Views
355
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 31, 2026
keel
H
Forced Induction On3 Turbo Kit- Parts list NEEDED - 302 Stock Motor
  • Hirothecool1
  • Feb 27, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
21
Views
2K
Fox 5.0 Mustang Tech Mar 7, 2026
slow84lx
S
D
Electrical Weird door wiring issues
  • Dakar09
  • Oct 20, 2026
  • Fox 5.0 Mustang Tech
Replies
4
Views
207
Fox 5.0 Mustang Tech Oct 21, 2026
Dakar09
D
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?