• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Serpentine belt gettin ate up????!!!!

  • Thread starter Thread starter neikoblu
  • Start date Start date Apr 26, 2006

neikoblu

New Member
May 9, 2005
63
0
0
Barksdale AFB, Lousyanna
Apr 26, 2006
#1
  • Apr 26, 2006
  • #1
Man I just don't get it...I bought a ribbed belt and it didn't last me but about 2 months and the ****** is shredded. Worst of all it took My A/C clutch with it. So I bought a new belt and before I put it on I checked all of the pulleys for play and none of them make noise so I would assume that the bearings are fine, but it is eating my new belt to peices...Belt paritcles are allover the altinator, water pump, compressor, well everywhere there is silver and that is visible to the eye. everything is tight, all brackets but I don't know what the cause is or how to fix it. Is there a way to check pully alignment or anything to fix this problem. Man this sucks.
 

srothfuss

Last night I stabbed the same guy 7 times in a row
Oct 17, 2004
1,796
3
0
Woodward Ave.
Apr 26, 2006
#2
  • Apr 26, 2006
  • #2
What parts of the belt are being chewed up?

Side of the belt = pulley alingment or walking

Bottom of belt = pulley that isn't spinning correctly
 

Vinnietbird

Member
Jun 2, 2005
584
3
19
Apr 26, 2006
#3
  • Apr 26, 2006
  • #3
I had that problem,and it turned out that the pulley on my steering pump (plastic0 had a piece broke off,and the sharp edge was eating my belts.New pulley,no problem.
 

neikoblu

New Member
May 9, 2005
63
0
0
Barksdale AFB, Lousyanna
Apr 27, 2006
#4
  • Apr 27, 2006
  • #4
It seems to be the sides of the belt. The inside-side of the belt that face like the motor. I will take a closer look at the power steering pump pulley. The only thing that I have changed since I dropped the motor in like a year and a half ago was a 3G alternator. I picked it up on EBAY and it fit fine after I notched the alternator bracket like they said that I would. Since I have underdrive pulleys, I saw on here that people were putting and overdrive pulley on the alternator so I did that as well, that pulley came from Summit. Lastly, I just recently replace the power steering pump. All I did was use a pulley puller and pressed the pulley on the new pump, pretty much standard. Is there a way to check pulley alignment? Maybe one of my pulleys are out of alignment and I just can't see it with the naked eye.
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
Apr 27, 2006
#5
  • Apr 27, 2006
  • #5
neikoblu said:
It seems to be the sides of the belt. The inside-side of the belt that face like the motor. I will take a closer look at the power steering pump pulley. The only thing that I have changed since I dropped the motor in like a year and a half ago was a 3G alternator. I picked it up on EBAY and it fit fine after I notched the alternator bracket like they said that I would. Since I have underdrive pulleys, I saw on here that people were putting and overdrive pulley on the alternator so I did that as well, that pulley came from Summit. Lastly, I just recently replace the power steering pump. All I did was use a pulley puller and pressed the pulley on the new pump, pretty much standard. Is there a way to check pulley alignment? Maybe one of my pulleys are out of alignment and I just can't see it with the naked eye.
Click to expand...

The best I can figure is that the P/S pump pulley either was not installed all the way on the shaft, or it is starting to back off for some reason.

You can confirm the pulley is installed properly by looking at the shaft, which should be flush with the pulley.


I have had good luck in the past 'eyeballing' the alignment of my pulleys. What I do is move my body so that the center of a couple of pulleys appear to be in line. Then withoug moving, look at the pulley that is in question. In your case either the Alt or p/s. I have not had very good luck using the front or back side of the pulleys to eyeball alignment.

jason
 

neikoblu

New Member
May 9, 2005
63
0
0
Barksdale AFB, Lousyanna
Apr 27, 2006
#6
  • Apr 27, 2006
  • #6
I jumped around the forum and found that sometimes the p/s pully can be press too far or not far enough as you said. I will eyeball it and see what comes up. This is what I am in question with though, why is there belt dust all over the place. If it were to be the p/s pulley then shouldn't it be localized there not all over the motor too. But thinking about it, it would seem feasable that the belt is simply carrying the belt dust. Wish me I guess
 
You must log in or register to reply here.

Similar threads

T
What's it Worth? 2002 GT conv/auto
  • tonydetesta
  • Jan 7, 2026
  • What is it Worth?!?!?
Replies
3
Views
639
What is it Worth?!?!? Jan 21, 2026
Mustang5L5
M
Progress Thread mnky99 2001 V6 evap core, ac compressor, heater core replacement
  • mnky99
  • Sep 5, 2025
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
1
Views
505
1996 - 2004 SN95 Mustang -General/Talk- Sep 5, 2025
mnky99
M
Engine Throwing codes 94, 33, 34, 44, and sporadic engine shutoff.
  • Ryu
  • Oct 9, 2024
  • Fox 5.0 Mustang Tech
Replies
11
Views
976
Fox 5.0 Mustang Tech Oct 16, 2024
89ripper
For Sale 94 Cobra 408w AOD Project For Sale
  • Labora
  • Oct 11, 2024
  • SN95 Mustangs For Sale (1994-04)
Replies
1
Views
1K
SN95 Mustangs For Sale (1994-04) Apr 7, 2025
Labora
New daily driver help needed.....not a mustang but mustang drivetrain.
  • Wayne Waldrep
  • Jun 17, 2024
  • Other Auto Tech
  • 3 4 5
Replies
80
Views
6K
Other Auto Tech Jul 28, 2024
manicmechanic007
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?