• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech

SN95 with Cobra front brakes

  • Thread starter Thread starter StinkinLincoln
  • Start date Start date Oct 27, 2011

StinkinLincoln

Member
Dec 9, 2006
240
0
17
Louisiana
Oct 27, 2011
#1
  • Oct 27, 2011
  • #1
I did the upgrade awhile ago. Its not stopping hard. ABS does not kick on and the tires do not lock up or skid. the car slows down, but not quick enough.

Do i need to put a proportioning valve in?
no abs/brake light. i had a bad rear wheel speed sensor but i fixed it.

Ideas?
 
T

turbogt

Member
May 1, 2003
723
16
19
Montana
Oct 27, 2011
#2
  • Oct 27, 2011
  • #2
StinkinLincoln said:
I did the upgrade awhile ago. Its not stopping hard. ABS does not kick on and the tires do not lock up or skid. the car slows down, but not quick enough.

Do i need to put a proportioning valve in?
no abs/brake light. i had a bad rear wheel speed sensor but i fixed it.

Ideas?
Click to expand...

Install the cobra master cylinder.. Cobras and GT's have different master cylinders..

And of course, make sure they are bled completely
 

sixt9coug

Member
Sep 30, 2009
222
3
19
Norwalk SoCal
Oct 28, 2011
#3
  • Oct 28, 2011
  • #3
Ditto on the above. Did you swap the MC too? I have the entire front kit on my car and it stops nice and clean. Very confident stops indeed.

Check to make sure it's bled right too.
 

StinkinLincoln

Member
Dec 9, 2006
240
0
17
Louisiana
Oct 29, 2011
#4
  • Oct 29, 2011
  • #4
No, stock GT MC. I guess i could bleed them again. No spungy pedal though like you normally get with air. Its more like feeling a lack of power assist for hard stops. just easy breaking i dont notice it to be any different than other cars.

i dont remember if i deglazed the pads or not, the rotors did get a little rusted from sitting but it all went away after i drove it.
 

SableSal

Member
Sep 17, 2009
295
3
19
Fresno, Californ-I-A
Oct 29, 2011
#5
  • Oct 29, 2011
  • #5
Something is wrong. Keep bleeding them.

I am running a GT Cylinder and Cobra brakes and my brakes do lock and ABS kicks in quite well. Also, I'm running stainless steel brake lines too, that might help.

But I would definitely bleed the brakes!

Good luck!
 

sixt9coug

Member
Sep 30, 2009
222
3
19
Norwalk SoCal
Oct 30, 2011
#6
  • Oct 30, 2011
  • #6
StinkinLincoln said:
No, stock GT MC. I guess i could bleed them again. No spungy pedal though like you normally get with air. Its more like feeling a lack of power assist for hard stops. just easy breaking i dont notice it to be any different than other cars.

i dont remember if i deglazed the pads or not, the rotors did get a little rusted from sitting but it all went away after i drove it.
Click to expand...

One of the problems that people report while using the GT MC is a hard pedal. Sounds like the proper MC and adapter lines would go a long way into giving you what you want.
 

gtsracer80

New Member
Sep 25, 2011
7
0
2
Oswego, IL
Nov 6, 2011
#7
  • Nov 6, 2011
  • #7
SableSal said:
Something is wrong. Keep bleeding them.

I am running a GT Cylinder and Cobra brakes and my brakes do lock and ABS kicks in quite well. Also, I'm running stainless steel brake lines too, that might help.

But I would definitely bleed the brakes!

Good luck!
Click to expand...

same here, no problems.
 

Bosko5.0

Active Member
May 18, 2006
1,067
0
37
longwood, FL
Nov 6, 2011
#8
  • Nov 6, 2011
  • #8
Take the pads off and check them I think they are glazed. Are they stock pads or aftermarket?
 

toyman

10 Year Member
Jul 19, 2007
1,944
54
79
Vernon BC
Nov 6, 2011
#9
  • Nov 6, 2011
  • #9
There could be other possible issues. First check the the check valve on the brake booster. If that's okay the other thing that can happen is for the booster diaphragm to split. If your pedal is hard and it's like trying to stop as if the engine is off the diaphragm should be suspect. I had that happen about a year ago.
 
You must log in or register to reply here.

Similar threads

Which SN95 axles for 93 LX, disc brakes, ABS rings?
  • dan50
  • Mar 22, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
15
Views
508
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Apr 3, 2026
7-UP BILL
Brakes FOX BRAKES ISSUES
  • PonyGTrider
  • Jan 11, 2026
  • Fox 5.0 Mustang Tech
  • 2 3
Replies
53
Views
2K
Fox 5.0 Mustang Tech Jan 31, 2026
Mustang5L5
Brake pad and rotor upgrade
  • Sparky714
  • Aug 7, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
16
Views
477
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 17, 2026
Sparky714
Cobra Brake Conversion - Spare Wheel/Tire Search
  • AeroCoupe
  • Aug 2, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
372
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 2, 2026
AeroCoupe
S
Fox Another try for the European guy to get his first Fox
  • Schargedfox
  • Aug 3, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
10
Views
313
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 4, 2026
DadLife0724
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 1994 - 1995 Specific Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?