• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

sticking idle

  • Thread starter Thread starter jmd2914
  • Start date Start date Sep 11, 2005
J

jmd2914

Founding Member
Sep 6, 2002
937
0
0
Napa, California
Sep 11, 2005
#1
  • Sep 11, 2005
  • #1
ok i was on my way home from work and out of no where my car jerks three times and then when i pushed my clutch in the rpms jumped up to 3000 rpm and stuck, with the clutch pedal still in. anyone got any ideas?
 
J

jmd2914

Founding Member
Sep 6, 2002
937
0
0
Napa, California
Sep 12, 2005
#2
  • Sep 12, 2005
  • #2
did search.....didnt find anything
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Sep 12, 2005
#3
  • Sep 12, 2005
  • #3
Once you put the car in neutral and released the clutch pedal, what did the idle do?

Did this happen again? Did it feel like a mechanical sticking (like the TB butterfly or throttle cable) or like an engine management glitch?

I would pull codes nonetheless. A code can be stored even if the CEL is not on. This happens often with 'burps' that come and go pretty fast.

More info will help folks to help you.
Good luck bud.
 
M

my$100project

New Member
May 12, 2005
208
0
0
Sep 12, 2005
#4
  • Sep 12, 2005
  • #4
Sounds mechanical to me. I mean if it was an engine problem it wouldn't have revved to 3000 just to keep from dying, IMHO. I would be willing to guess you have a sticking TB or cable/peddle problem. Have you taken the cable off recently for some reason? Did you adjust the position where the cable connects to the TB? Is it possible the cable is ran in a way where it got caught somewhere pulling back the tb? Have someone else get inside and see if they can duplicate. My guess is either a cable or peddle problem. Never seen a tb "stick" open before. Anythings possible.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Sep 12, 2005
#5
  • Sep 12, 2005
  • #5
TB butterflies can stick open. Some of the aftermarket units have screws on the butterfly axis to allow adjustment and some folks have had to hollow out the bore a little to keep the butterfly from sticking. This is almost always at WOT though.
 
J

jmd2914

Founding Member
Sep 6, 2002
937
0
0
Napa, California
Sep 12, 2005
#6
  • Sep 12, 2005
  • #6
when the car is in neutral with the clutch out the rpms still stick at 3000. the idle is really rough too. im not sure if that helps, but its a start.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Sep 12, 2005
#7
  • Sep 12, 2005
  • #7
So is it stuck at all times now?
 
J

jmd2914

Founding Member
Sep 6, 2002
937
0
0
Napa, California
Sep 12, 2005
#8
  • Sep 12, 2005
  • #8
not all the time, its just every once in a while, ill be driving and it will kick up to 3000 and stick
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Sep 12, 2005
#9
  • Sep 12, 2005
  • #9
jmd2914 said:
not all the time, its just every once in a while, ill be driving and it will kick up to 3000 and stick
Click to expand...
If the problem clears when you turn the iginiton switch off & and then restart the car, replace the TPS.
 
J

jmd2914

Founding Member
Sep 6, 2002
937
0
0
Napa, California
Sep 12, 2005
#10
  • Sep 12, 2005
  • #10
ive replaced it once about two years ago....about how long does a tps last?
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Sep 13, 2005
#11
  • Sep 13, 2005
  • #11
jmd2914 said:
about how long does a tps last?
Click to expand...
Apparently about two years.

The TPS should be about a 15 dollar part - worth a shot. I try not to toss parts at problems if I can help it, but with an intermittant issue like this, it can be difficult to 'catch' it when it is acting up so you can troubleshoot it (you are not going to leave it idling at 3K RPM, and once you shut down and restart, it probably fixes itself). Might be worth tossing a few bucks at - esp based upon the wise-one who recommended it.
 
J

jmd2914

Founding Member
Sep 6, 2002
937
0
0
Napa, California
Sep 13, 2005
#12
  • Sep 13, 2005
  • #12
true, ill give it a shot and see how it goes, is there any way i can test the tps i have?
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Sep 13, 2005
#13
  • Sep 13, 2005
  • #13
jmd2914 said:
true, ill give it a shot and see how it goes, is there any way i can test the tps i have?
Click to expand...
Here is some info that can help (pics and basic procedures).

For testing the sensor, I hook up as is done in the above-link. But then with the key-on (Engine off!) slowly open the throttle. Watch the Meter (an analog VOM works best for this test) as you open the throttle. The meter's sweep should be completely linear with no spikes or dead spots.

The thing is that your TPS probably tests fine - you would need to test it when it is acting up (has your idle stuck at 3K RPM), which is not very practical. That was my point above.

Good luck.
 
M

my$100project

New Member
May 12, 2005
208
0
0
Sep 13, 2005
#14
  • Sep 13, 2005
  • #14
TPS--Duh, Why didn't I think of that? J or Hissin have either of you had to work on the relatively new "TBW" (throttle by wire) cars yet? What a nightmare.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Sep 13, 2005
#15
  • Sep 13, 2005
  • #15
my$100project said:
TPS--Duh, Why didn't I think of that? J or Hissin have either of you had to work on the relatively new "TBW" (throttle by wire) cars yet? What a nightmare.
Click to expand...
Not for me, and I hope that I dont have to any time soon. I am kind of an old-school kind of guy. I have read a bit about the Spanish Oak workings and I would not want any part of that.

I would add that JR is a high-tech guy, so he probably knows all about that stuff.
 

90mustangGT

I felt sorry for girls because
Founding Member
Jan 15, 2002
2,773
17
89
Dallas, GA
Sep 14, 2005
#16
  • Sep 14, 2005
  • #16
Do the TPS test as Hissin50 describes. Another cause could be a massive vacuum leak, stuck IAC, binding throttle cable, or even a dirty TB.
 
You must log in or register to reply here.

Similar threads

L
Engine 85 GT Excessive Idle
  • lutzkecj
  • Sep 18, 2026
  • Fox 5.0 Mustang Tech
Replies
5
Views
367
Fox 5.0 Mustang Tech Sep 21, 2026
86HO5.0
8
2001 SVT Cobra slow return to idle speed
  • phil2001svt
  • Oct 21, 2026
  • SVT Tech Forum
Replies
3
Views
150
SVT Tech Forum Nov 2, 2026
phil2001svt
2000 GT-Front Brakes Not Releasing
  • stormsedge
  • Aug 7, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
5
Views
248
1996 - 2004 SN95 Mustang -General/Talk- Aug 7, 2026
Bronco2fan
B
T
Drivetrain TREMEC TKX 1–2 Grinding Issue at ~4,000 Miles + Poor Warranty/Customer Service Experience
  • Ttopfoxguy
  • Oct 10, 2026
  • Fox 5.0 Mustang Tech
Replies
5
Views
317
Fox 5.0 Mustang Tech Oct 15, 2026
JMG9350
J
C
Electrical HELP! 1989 5.0 Stick, Voltage Bleed onto Ignition Trigger wire
  • ChickenDeluxe
  • May 14, 2026
  • Fox 5.0 Mustang Tech
Replies
7
Views
380
Fox 5.0 Mustang Tech May 24, 2026
ChickenDeluxe
C
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?