• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

t-5 rebuild

  • Thread starter Thread starter stprorolla49
  • Start date Start date Mar 23, 2006

stprorolla49

Active Member
Oct 9, 2004
1,455
15
39
Fairfield, CT/North Jersey
Mar 23, 2006
#1
  • Mar 23, 2006
  • #1
before you guys jump down my throat, yes i searched this topic, and yes i read every thread....that being said, i need to rebuild my t-5 because 3rd gear grinds when i shift any faster than clicking it 1/2 way, then all the way into gear...it jsut started, and i wanna rebuild before it gets worse....also, this is my daily driver so it cant be out of comission for too long, so if i started this on a friday night, could i have teh car running again by sunday afternoon? my dad and i are very mechanically inclined, and we have the tools to do this, just never done a t-5...only a few muncie 4spds....last thing, does this kit below look like a good kit? thanks guys!

http://cgi.ebay.com/ebaymotors/T5-W...ryZ46103QQssPageNameZWDVWQQrdZ1QQcmdZViewItem
 

TheBocSez

New Member
Feb 3, 2004
652
0
0
Converse, TX
Mar 23, 2006
#2
  • Mar 23, 2006
  • #2
Dont know much about rebuilding T5s or the time it will take, but here is a link that may help you along. I also have a manual in PDF file but I dont know how to attach it.

http://www.oldwestracing.com/
 

GearHd6

Member
Jul 19, 2005
459
0
18
Ashford, CT
Mar 23, 2006
#3
  • Mar 23, 2006
  • #3
Odds are you're going to get in there and find more wrong than you think. Seems to be how it always works out. Probably need a gear or 2 because you'll see the little syncro dogs are rounded over.
 

GearHd6

Member
Jul 19, 2005
459
0
18
Ashford, CT
Mar 23, 2006
#4
  • Mar 23, 2006
  • #4
Go to this link : http://www.ttcautomotive.com/English/products/T-5.asp

and click on "service manual" if you have Acrobat Reader so you can view a PDF file.
 
B

BlackBaer5.0

Member
Nov 26, 2003
100
0
16
Mar 23, 2006
#5
  • Mar 23, 2006
  • #5
WOW, that www.oldwestracing.com site has some great write ups,
espeically that t5 rebuild one, very complete and thorough
 

dragnazz5.0

My "0" key d0esn't w0rk, s0 I have t0 use the zer0
Nov 19, 2005
815
5
18
mooresville, nc
Mar 23, 2006
#6
  • Mar 23, 2006
  • #6
nothing to it. just make sure you have all the parts that you could possibly need before you start. shouldnt even take you a whole day. good luck
 

stprorolla49

Active Member
Oct 9, 2004
1,455
15
39
Fairfield, CT/North Jersey
Mar 23, 2006
#7
  • Mar 23, 2006
  • #7
thanks guys...im afraid this is gonna cost me more than i am bargaining for....
 
W

wazazzle

New Member
Mar 30, 2005
618
1
0
In the dumpster behind McDonalds. WA
Mar 23, 2006
#8
  • Mar 23, 2006
  • #8
Mine needs a rebuild too. What I'm doing is pulling a 4cyl t5 $65 local pullpart and replacing the pilot shaft bearing $10 ebay. My 89 t5 torque rating is only 260lbs, vs 240lbs 4cyl t5. So 20lbs not that big diff for me since mines stock and I usually shift at 4,000. It should prob last few months or 1yr, well worth $75 imo. Yank my org T5 out and open her up to see exactly what need replacing cause you never know. I'll most likely get a master rebuild kit $220 and self rebuild. I bought a t5 rebuild video - highly recommended. You will need a shop press too if you don't already have one. That's another $130 at harbor frieght.
 

jrichker

StangNet's favorite TOOL
In Remembrance. Thank you for your contributions
Mar 10, 2000
27,512
2,813
234
Dublin GA
Mar 24, 2006
#9
  • Mar 24, 2006
  • #9
See http://www.ttcautomotive.com/English/onlineorder/product.asp to download a FREE service manual for T5 or Tremec 3550
You will need the Adobe Acrobat viewer which is also a free download – http://www.adobe.com/products/acrobat/readstep2.html

See http://www.hanlonmotorsports.com/ or http://www.ddperformance.com for parts

A T5 rebuild kit with syncros, bearings and other small parts costs about $160. It does not include any gears or shafts.

http://cartapes.com also has a video on how to rebuild your T5 or Tremec. It costs less than $20, and is worth every penny of it.

I did a Tremec 3550 rebuild, and it wasn't that difficult. The video was an immense help, and I would recommend viewing it. At $20, it will give you an opportunity to look and decide for yourself if you think that it is something you want to try to do.

Transmission removal tips...

Labor time: by yourself, first time - 4-6 hours from the time the car gets up on jackstands until the trans sits on the ground & the bellhousing is off. You'll have about the same amount of time to get it reassembled & back in service.

You need both metric & US tools to do the job, the body bolts are metric & the trans mount & engine bolts are US.

The rear driveshaft bolts are 12 MM, 12 point and require a first class box end wrench (ring spanner if you are English or Canadian) to remove them. Don't get cheap here or you will regret it. I set the emergency brake and apply a foot to the wrench to loosen the bolts. Notice the paint marks on the driveshaft & rear end flange: align them the same way they came off. If there aren't any marks, get out your paint spray can & make your own marks.

Be sure to drain the fluid before you remove the trans or you will get to wear it. The best time to do this is before you remove the driveshaft. Have a catch pan in place to get the fluid that comes out of the trans when you pull the driveshaft yoke out. T5's take a good grade of ATF, Tremec 3550 & TKO use 2 3/4 quarts GM Syncromesh at $9+ a quart.

The speedo cable pulls straight out of the adapter, don't pull the clip out of the adapter. It re-installs the same way: push hard on the cable. You can unbolt the speedo cable adapter and pull it out of the trans: this may be the easiest way. Then you don't have to worry about pulling the cable apart. I have had the cable housing separate from the metal sleeve when I it pulled it out. If you do unbolt the adapter, then cover it with a plastic zip bag.

The H pipe will have to come off and the studs are likely to be very rusty. Soak them with PB Blaster or WD 40 overnight if possible. When you re-assemble the H pipe & exhaust bolts, use lots of antiseize. That way the will be easy to remove next time (yes, there will be a next time!). Use care in disconnecting the O2 sensor wiring that you don't damage the clips that help hold the connector halves together. Be sure to tie wrap (zip tie) the wires out of the way when you re-assemble them.

Identify & mark the neutral safety switch & backup light switch wiring. The connectors are different, but it helps you to get them back on it the right places.

Look at the rubber on the rear trans mount and replace the mount if it is oil soaked or deteriorated. The same goes for the rubber crossmember bushings.

If you have a T5, you may be able to remove the trans & re-install it if you can bench press the 75 lbs that it weighs. If 75 lbs is too heavy, don't hurt yourself, get a trans jack. If your car has a Tremec 3550 or TKO, you will need a helper or trans jack because it weighs 100 + lbs. I built a trans jack from 2x2 angle iron, some swivel casters, 2x4's, 2x6's and a cheap floor jack. PM me if you are interested & I will send you the photos (8 MB) with the write up.

While you are at it, replace the stock cable & quadrant if it is still present. When you buy the cable & quadrant and maybe a firewall adjuster, make sure they are all the same make. That way you have some assurance that they work together. I have a FMS quadrant & cable, & have had no problems with it. The FMS adjustable cable doesn't stretch and operates smoothly. The only thing is that you have to get under the car to make any adjustments. A firewall adjuster would help here to make the fine adjustment.
 

Busted07

I need my gorilla to be about an inch longer.
Nov 15, 2005
0
3
0
Mar 24, 2006
#10
  • Mar 24, 2006
  • #10
Just in case you need any more info (which i doubt) http://pomoforacing.com/tech/T5Rebuild2002.pdf that is helping me rebuild mine right now.. well actually, im not doing the gears, but i bought a block & ring kit from hanlon, and had someoen else install it. i just took my tranny apart to make sure everything looks good before i bolt it in
 
You must log in or register to reply here.

Similar threads

T
Oil burning on my recently buil 302
  • The blk67
  • May 15, 2026
  • Fox 5.0 Mustang Tech
Replies
3
Views
250
Fox 5.0 Mustang Tech May 15, 2026
Noobz347
Engine Suggestions on an engine rebuild. Stock cam/GT40Ps or aftermarket on both for a fun weekend driver?
  • MadSquirrelTech
  • Apr 28, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
23
Views
1K
Fox 5.0 Mustang Tech May 7, 2026
MadSquirrelTech
C
Drivetrain T-5 transmission issue
  • Ch3No2
  • Jul 11, 2025
  • Fox 5.0 Mustang Tech
Replies
3
Views
494
Fox 5.0 Mustang Tech Jul 18, 2025
2000xp8
H
Forced Induction On3 Turbo Kit- Parts list NEEDED - 302 Stock Motor
  • Hirothecool1
  • Feb 27, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
21
Views
2K
Fox 5.0 Mustang Tech Mar 7, 2026
slow84lx
S
Engine A/C QUESTION
  • Mindseye007
  • Jun 5, 2025
  • Fox 5.0 Mustang Tech
  • 2 3 4
Replies
60
Views
3K
Fox 5.0 Mustang Tech Jun 22, 2026
nicholase
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?