• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-

T5 Trans Questions

  • Thread starter Thread starter teebluestang
  • Start date Start date Nov 6, 2016

teebluestang

Member
Jan 30, 2016
57
3
8
Sewell N.J
Nov 6, 2016
#1
  • Nov 6, 2016
  • #1
I recently purchased a 94 95 t5 with bell housing. Will it fit my 1988 bell housing and or if I install the one I purchased starter doesn't fit bell housing . Thoughts ?
 

broncojunkie

Active Member
Apr 12, 2014
92
24
29
Nov 6, 2016
#2
  • Nov 6, 2016
  • #2
You can use your old bell, but you would either have to swap over the old input shaft and retainer or use an adaptor plate. I think LMR sells them.

I'm not 100% on the starter. I thought they were the same.
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,378
18,123
224
Massachusetts
Nov 6, 2016
#3
  • Nov 6, 2016
  • #3
Starters are compatible. The issue is the 94+ T-5's got a longer input shaft, and the bellhousing was stretched to accommodate.

In order to use it with the 1988 bellhousing, you'll need to swap the input shaft to a 90-93 variety, as well as the bearing retainer
 

broncojunkie

Active Member
Apr 12, 2014
92
24
29
Nov 6, 2016
#4
  • Nov 6, 2016
  • #4
https://lmr.com/item/LRS-6392A-S/Mustang-T-5-Bellhousing-Adapter-Plate-83-93

This is the adapter plate I was talking about. It takes up the slack, so to speak, if you're using a longer sn95 input shaft with a fox bellhousing.
 

Boosted92LX

It's only an inch or two. What's the big deal?
15 Year Member
Dec 19, 2010
5,721
4,244
224
Nov 6, 2016
#5
  • Nov 6, 2016
  • #5
I think before I spent $160 on that plate, I'd go find a piece of aluminum and make one. Crazy.
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,378
18,123
224
Massachusetts
Nov 6, 2016
#6
  • Nov 6, 2016
  • #6
Downside to the plate is it moves the shifter back about 3/4". Some people like that, but you might need to tin snip the rear of shifter hole.

Also since the trans moves back, driveshaft lengyt should be paid attention to


Sent from my iPhone using Tapatalk
 

broncojunkie

Active Member
Apr 12, 2014
92
24
29
Nov 6, 2016
#7
  • Nov 6, 2016
  • #7
I thought that plate was pricey too, but I would like to have one. I have 3 fox bodies and a few t5's lying around...a couple are 99-04. It would make it easier to swap them around. I like having options I guess.

Heck, I might use a 3.8 bellhousing and go to 11" clutch. And for some reason, my 88gt t5 sits too far forward. Probably because of the aftermarket motor mounts. It would benefit from a slightly deeper bellhousing.
 

teebluestang

Member
Jan 30, 2016
57
3
8
Sewell N.J
Nov 6, 2016
#8
  • Nov 6, 2016
  • #8
Mustang5L5 said:
Downside to the plate is it moves the shifter back about 3/4". Some people like that, but you might need to tin snip the rear of shifter hole.

Also since the trans moves back, driveshaft lengyt should be paid attention to


Sent from my iPhone using Tapatalk
Click to expand...
I was told that the drives haft would he fine. But thank you for making me keeping an eye out for it
 

teebluestang

Member
Jan 30, 2016
57
3
8
Sewell N.J
Nov 16, 2016
#9
  • Nov 16, 2016
  • #9
Mustang5L5 said:
Starters are compatible. The issue is the 94+ T-5's got a longer input shaft, and the bellhousing was stretched to accommodate.

In order to use it with the 1988 bellhousing, you'll need to swap the input shaft to a 90-93 variety, as well as the bearing retainer
Click to expand...

Can I use my starter from the 1988 bellhousing on the 1994
 

Black1987

my wife Bedazzled my input shaft
15 Year Member
Jan 9, 2011
1,064
595
174
NC
Nov 17, 2016
#10
  • Nov 17, 2016
  • #10
Just an FYI when it slides the shifter back, the cross member might not bolt up to mounts. I did vice versa and had to change the input shaft.
 

teebluestang

Member
Jan 30, 2016
57
3
8
Sewell N.J
Nov 17, 2016
#11
  • Nov 17, 2016
  • #11
Black1987 said:
Just an FYI when it slides the shifter back, the cross member might not bolt up to mounts. I did vice versa and had to change the input shaft.
Click to expand...

I'm going to use the 1994 bellhousing hope it all workS
 

broncojunkie

Active Member
Apr 12, 2014
92
24
29
Nov 17, 2016
#12
  • Nov 17, 2016
  • #12
Starter should be the same.
 
You must log in or register to reply here.

Similar threads

M
85 Capri 5.0 transmission rattle
  • Mamaclean
  • May 2, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
2
Views
260
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- May 17, 2026
Mamaclean
M
C
Help with manual conversion
  • CPH89LX
  • Aug 23, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
20
Views
726
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Aug 27, 2026
2000xp8
K
3.8 T5 & Bellhousing to 1987 Lincoln 5.0
  • ks65stang
  • Mar 2, 2026
  • Other Auto Tech
Replies
3
Views
575
Other Auto Tech Mar 3, 2026
Noobz347
T5 5th gear 89 gt
  • mac_55
  • Mar 19, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
2
Views
292
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Mar 20, 2026
Mustang5L5
B
Flywheel
  • Barry
  • Mar 10, 2026
  • 1974 - 1978 Mustang II Talk & Tech
Replies
4
Views
333
1974 - 1978 Mustang II Talk & Tech Mar 11, 2026
Barry
B
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?