TCP Subframe Connectors & Magnaflow Exhaust

69 Rustang · Nov 28, 2006

Has anyone tried to install the Total Control subframe connectors with the center x-brace AND the Magnaflow stainless X-pipe exhaust kit? If so, did it fit without cutting up one or the other?

fvike · Nov 29, 2006

I haven't, but I have a TCP center brace that don't fit, because my exhaust doesn't run along the driveshaft tunnel. I.E if the Magnaflow system does that, has offset muffler inlet and center outlet, it should fit.
My current exhaust mufflers has both center inlet and outlet, and that is enough for the TCP brace not to fit.
Myself I was thinking about getting a complete Flowmaster exhaust kit for my car. By the look of it, it will fit.

Cannoball888 · Nov 29, 2006

No, 2.5" Magnaflow will not fit the trans tunnel with the center brace, at least on a 65 Mustang. I took it to a custom exhaust shop for that answer. Though. 2.25" pipes would fit.

68FBJJZ109 · Nov 29, 2006

Maybe you could try a Flat X pipe Dr. Gas has them, that should help with clearances issues.

jamison42166 · Nov 29, 2006

i have the TCP subframe your talking about but i have H Pipe.. i still had to run custom ehaust and tuck it near the tunnel.

http://new.photos.yahoo.com/jamison42166/album/576460762343079015/photo/294928803637372507/9

http://new.photos.yahoo.com/jamison42166/album/576460762343079015/photo/294928803637372850/10

Cannoball888 · Nov 29, 2006

Is your exahust 2.5"? It looks like 2.25". I found that the Magnaflow X pipe is not the problem. It's the dual 2.5" pipes that must fit in the tranny channel and above the center brace. 2.5" is too big and it will rub the driveshaft if you can even get them in at all.

69 Rustang · Nov 29, 2006

jamison42166 said:
i have the TCP subframe your talking about but i have H Pipe.. i still had to run custom ehaust and tuck it near the tunnel.
QUOTE]

I see you have R&P on the front--looks like the TCP piece there as well. I want R&P, but have ceramic coated headers I really don't want to give up/cut. What kind of headers/engine combo are you running? Based on the other pics it would be a 289 4V but not sure about your headers. No shortage of money spent under your car--wow, I am jealous!

jarrettdad · Nov 29, 2006

I just ordered the TCP subframe connectors and cross brace. How do you like it?

68FBJJZ109 · Nov 29, 2006

The SFC are quite nice, though like these guys i am having exhaust issues, but far worth it i believe especailly with the x brace. They stiffened my car up quite a bit.

Robdogg67 · Nov 30, 2006

I just did it all from scratch - TCP subframes, TCP center connector, magnaflow 2.5 with X-pipe system and all this with an new AOD tranny. It was very tight, especially around the front U-joint and directly around the AOD crossmember. I anticipated this clearance issue and ordered the AOD x-member from JBA which is awesome in terms of clearance for exhaust. Which by the way was a terrible company to work with (I could post a whole other thread on how they fell on their face with me on this one), every update was 2 weeks but it took them over 3 months, pitiful customer service, I even tried to reach the owner (Jay) but of course he chose not to respond either. Their products are nice but I only mention it so that if you need something thats not in stock, don't waste your time with them. Anyway, the exhaust was tricky as I chose FPA longtubes and the exhaust shop had a challenging time getting it to clear everything but they made it work.

The bottom line is that the lowest point under my car (67 FB) is the AOD deep pan and everything else tucks up tight but nice, hell I even have my stock handbrake working decent under there. It can be done.

Sicarius428 · Nov 30, 2006

I had to get custom exhaust put in to get around the center section of my subframes. I have long tubes and a C6 so there was no chance of fitting any sort of H or X pipe but they did run 2.5 inch to the mufflers.
Kevin

69 Rustang · Nov 30, 2006

Sounds like a custom exhaust is a must with the SFC and Xbrace. Is the Dr. Gas X-crossover stainless or mild steel? Anyone know how much it is? Thanks

jamison42166 · Nov 30, 2006

im running ceramic coated tri -y headers... no issues with the headers clearing anything since i have the power rack i dont have to worry about the stock power steering interfering. the engine is a 289 4 v i just got done redoing it.. edelbrock performer RPM heads, intake, cam, 750 CFM carb with electric choke, new lifters pushrods and in 2 weeks im putting in roller rockers.
I have a power steer pump out of a 93 5.0 a march performance billet pulley underdrive and cool flex hoses

http://new.photos.yahoo.com/jamison42166/album/576460762357207544/photo/294928803836864288/0

jamison42166 · Nov 30, 2006

Slobin3d · Aug 30, 2011

This thread is very helpful I am looking at doing the TCP SFC on my car, It will see some SCCA in it's life, I', also looking into the front end conversion as well

67topless · Sep 1, 2011

Check my custom 2.5 exhaust:

http://1967stang.com/Gallery/albums/Mustang/Exhaust/exhaust_I.JPG
http://1967stang.com/Gallery/albums/Mustang/Exhaust/exhaust_II.JPG

This is a convertable which is different than your application; but I am running Hooker long tubes and I've purchased the TCP sub frame connectors including the center cross member.

TCP Subframe Connectors & Magnaflow Exhaust

69 Rustang

Member

fvike

Member

Cannoball888

New Member

68FBJJZ109

Member

jamison42166

Member

Cannoball888

New Member

69 Rustang

Member

jarrettdad

New Member

68FBJJZ109

Member

Robdogg67

New Member

Sicarius428

Active Member

69 Rustang

Member

jamison42166

Member

jamison42166

Member

Slobin3d

Active Member

67topless

Member

Similar threads

TCP Subframe Connectors & Magnaflow Exhaust

Member

Member

New Member

Member

Member

New Member

Member

New Member

Member

New Member

Active Member

Member

Member

Member

Active Member

Member

Similar threads

Privacy & Transparency

Privacy & Transparency