• Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SVT Tech Forum

the new guy, with some questions.

  • Thread starter Thread starter 8urv10
  • Start date Start date Oct 3, 2007

8urv10

New Member
Oct 3, 2007
0
0
0
Oct 3, 2007
#1
  • Oct 3, 2007
  • #1
hey everyone. well i just picked up a 2003 svt cobra vert and love it!! im new to the whole cobra thing though and thought i could get some good answers from here with everyone. its modded pretty good, 60 lb injectors, fuel pumps, intake, ported eaton, all pullies including a 3.100 upper, 3.73 gears, twin disk, subframe connectors, roll bar, etc.. im currently running rich up top (the initial wack is a 11.0:1 and at around 5k its down to a 10.6:1 a/f ratio) thanks to my lm1 wideband. i am trying to get soem dyno time set up but was wondering how efficient my blower would be with a 2.760 or a 2.930 upper pully. i have both. im hoping for around 500rwhp after my tune on just pump and boost. am i asking for too much. also, upon start up sometimes, it will blow out some smoke (oil). i asked a buddy of mine with a kb 2.4 cobra and he said it is probably in need of a pre filter for the pcv system. sound about right to anyone? i went and ordered one anyways. the car was checked out by a FORD mechanic who said everything was in great condition including the motor. anyways, thanks to anyone who can chip in any info..
 
U

Uncle Meat

Banned
Jun 13, 2002
0
1
0
Prattville, Alabama
Oct 4, 2007
#2
  • Oct 4, 2007
  • #2
Funny that the previous owner went through the trouble of upgrading to 60lb injectors and all, yet is only running a 3.10 upper on a ported Eaton? You sure there isn't a lower on the car? Might want to measure it before you go slapping a new, smaller upper. What is the current RWHP now with this setup? With your mods and 16-17lbs of boost you should be at or above 500RWHP.

As for the puff of smoke on start-up.... that's a common problem with these 03/04 Cobra's, even stock ones. The most common cause is oil blow by being sucked back into the motor from the PCV. This can be more pronounced with additional boost. Other folks say it's from a small amount of oil which leaks down around the valve guides. Mine even when stock used to do it and still does today.

U.M.
 

8urv10

New Member
Oct 3, 2007
0
0
0
Oct 4, 2007
#3
  • Oct 4, 2007
  • #3
he gave me a bunch of stock parts, nad there area a couple of im guessing lower pullies? thanks for the imput on the smoke. i heard that it was common. i think it might be sitting around 425 rwhp right now cause of the crappy tune. my last car was a 97 eagle talon that i built up and was sitting at 340awhp, and i can tell it has alot more torque, but i fell it should have more "go".
 
U

Uncle Meat

Banned
Jun 13, 2002
0
1
0
Prattville, Alabama
Oct 4, 2007
#4
  • Oct 4, 2007
  • #4
Just for S&G's you might want to go measure the lower pulley from edge to edge just to see if it's stock or not. All the mods you listed for the car just don't add up right with only a 3.10 upper? Sounds like the tune is rich because the car used to be running more boost. I get this funny feeling that it used to have a 6 or 8 lb lower on it, but now it no longer does for some reason? Something is kind of fishy.

U.M.
 

8urv10

New Member
Oct 3, 2007
0
0
0
Oct 4, 2007
#5
  • Oct 4, 2007
  • #5
well i know for a fact that it was detuned for the sale, ant it was running more boost and race gas at one point. that is what it was tunned for. i will measure them later and get back to you.
 

8urv10

New Member
Oct 3, 2007
0
0
0
Oct 4, 2007
#6
  • Oct 4, 2007
  • #6
alright, just looked at it, the pully directly under the upper measures like 3.5inches, the one to the right of that, is like 3.75, and the idler pully is about 4 inches. also, is there a linky about how to operate an sct xcal tuner? i have one for the car. i dont think its the live wire model though.
 
U

Uncle Meat

Banned
Jun 13, 2002
0
1
0
Prattville, Alabama
Oct 4, 2007
#7
  • Oct 4, 2007
  • #7
8urv10 said:
alright, just looked at it, the pully directly under the upper measures like 3.5inches, the one to the right of that, is like 3.75, and the idler pully is about 4 inches. also, is there a linky about how to operate an sct xcal tuner? i have one for the car. i dont think its the live wire model though.
Click to expand...
Well the pulley I was referring to is the crank pulley. The one all the way at the bottom. It should be 7.5 inches across if it's stock.

As for the SCT Xcal... what is it you want to do? I wouldn't use it to mess with any of the parameters of your tune if I were you. Your car is highly modified and you could risk messing it up if you were to try and adjust your A/F with the xcal at this point. Do you know if the previous owner left any of the custom tunes loaded in it when he sold you the car?

U.M.
 

8urv10

New Member
Oct 3, 2007
0
0
0
Oct 4, 2007
#8
  • Oct 4, 2007
  • #8
ok, my bad, just checked it and it is stock. im going to get it tuned this weekend, just set up an appointment. is there anything i should know in general about these cars?
 
U

Uncle Meat

Banned
Jun 13, 2002
0
1
0
Prattville, Alabama
Oct 4, 2007
#9
  • Oct 4, 2007
  • #9
8urv10 said:
ok, my bad, just checked it and it is stock. im going to get it tuned this weekend, just set up an appointment. is there anything i should know in general about these cars?
Click to expand...
Have you read this most awesome 03/04 Cobra FAQ yet? It's located here: http://www.stangshiftergaskets.com/2003_2004faqs.htm

U.M.
 

8urv10

New Member
Oct 3, 2007
0
0
0
Oct 4, 2007
#10
  • Oct 4, 2007
  • #10
now thats what im talking about!! thanks for the linky!!!!
 
You must log in or register to reply here.

Similar threads

R
New guy...
  • Rabbit14
  • Oct 18, 2025
  • The Welcome Wagon
Replies
0
Views
93
The Welcome Wagon Oct 18, 2025
Rabbit14
R
S
Fox '87 GT can't get to stay running
  • spilly
  • Mar 29, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
27
Views
685
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 20, 2026
spilly
S
New Member with a 1992
  • Clutchfork
  • Oct 18, 2025
  • The Welcome Wagon
Replies
5
Views
283
The Welcome Wagon Oct 19, 2025
Clutchfork
J
Car Diagnosis
  • j.2016
  • Aug 31, 2025
  • 2015 - 2023 (S550) Mustang -General/Talk
Replies
3
Views
308
2015 - 2023 (S550) Mustang -General/Talk Aug 31, 2025
Noobz347
Place to Avoid: Jamison Auto Group in Gulfport, MS
  • D Durden
  • Oct 20, 2025
  • 1965 - 1973 Classic Mustangs -General/Talk-
  • 2 3
Replies
45
Views
2K
1965 - 1973 Classic Mustangs -General/Talk- Feb 4, 2026
nickyb
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1996 - 2004 SN95 Mustang -General/Talk-
  • SVT Tech Forum
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?