Drivetrain TKX Shifter Position Question

fasterthangas · May 29, 2026

Those of you who have installed a TKX into a 94-95 GT; how did the TKX shifter sit in relation to your seating position?

What was your solution?

fasterthangas · Jun 5, 2026

Nobody has installed a TKX in their SN95?

DadLife0724 · Jun 5, 2026

Only SN95 I had was a V6. Hopefully someone else will be along shortly.

AeroCoupe · Jun 5, 2026

Need more info. Do you have a TKX installed and if so what shifter is on it? How tall are you? Is your seat all the way back? How far do you tilt the seat back? If you do have a TKX installed what exactly do you not like about the shifter position?

fasterthangas · Jun 5, 2026

I'd just like to know where the TKX shifter stub sits compared to the factory T5 shifter stub. Does the TKX shifter stub sit further forward than the factory T5 stub? Normally if a Fox T5 and bellhousing are installed into a 94-95 GT, the shifter stub will sit 5/8" to 3/4" forward of the factory 94-95 position due to the shorter Fox input shaft and shallower Fox bellhousing.

My TKX is not installed yet and I'd like to order an aftermarket shifter before I do. I know where I need the shifter to be while sitting in my fixed seating position.

Thanks.

AeroCoupe · Jun 5, 2026

So they do not make a TKX that has the 3/4” longer input shaft for a 94/95 car. So if you are putting one in it will have to have a Fox bell housing which may or may not work due to the clutch fork position (read clocking). If it will work then it will move the shifter forward 3/4” and it has been documented that in. Fox car it moves the shifter 1” to the passenger side.

fasterthangas · Jun 5, 2026

Yup, I realize that. That's why I mentioned a Fox T5 and bell housing in a SN95. The Fox T5 sits 5/8" - 3/4" forward when installed in a SN. I'd like to know if a TKX shifter will sit that same distance forward of the SN T5 factory position.

fasterthangas · Jun 5, 2026

Just like Christmas.

AeroCoupe · Jun 5, 2026

The TKX shifter in my 93 sits exactly in the same position the T5 shifter did in relation to the front and back of the car. With regards to left and right is was 1” to the passenger side.

fasterthangas · Jun 5, 2026

AeroCoupe said:
The TKX shifter in my 93 sits exactly in the same position the T5 shifter did in relation to the front and back of the car. With regards to left and right is was 1” to the passenger side.

Thanks. That means that the TKX shifter will sit forward of the factory SN T5 shifter in a SN car. This helps me with the offsets that I need for a shifter.

Noobz347 · Jun 6, 2026

If you end up not liking the position of the shifter, I'm pretty sure that an MGW shifter for the TKX should help put it where you want it:

Drivetrain Post in thread 'Short throw shifter for Tremec TKX?'

Jan 31, 2024

Mgw now has an option

Looks like they released one in late 2023.

fasterthangas · Jun 6, 2026

I have a MGW on my GForce and love it. I wanted one for the TKX but I need a handle that curves back towards me. They show only one handle that's straight up and down. I sit in a solid mounted Kirkey seat and I'm held in place with a 5 point harness.

AeroCoupe · Jun 6, 2026

They have three different handles. I know because I just put a TKX in my 93. Call them.

limp · Jun 6, 2026

Not sure if this will help but here are two pictures from a 1983 car with a TKX behind a SROD bellhousing...

WhiteCobra95 · Jun 6, 2026

I'm super interested in this as well. Please post pictures when you get it in. It's very hard to find info regarding the TKX and '94-'95 installations. I want to put one in my car, but I don't want to cut up the sheet metal to make it fit. It's been a long time since I've had it apart, so I don't remember how much extra room there was around the T5's shifter. I'm also wondering what this will do to fitting the upper boot around the TKX's shifter base.

As far as the reach goes, the SN shifter location already sits pretty far forward for someone like me with long legs and the seat as far back as it will go. I think the guys are right that an MGW will be the best way to recover the one-inch passenger side bias and get the shift knob far enough back. Their "comfort" shifter handle has a stock-style kick back which might work.

AeroCoupe · Jun 7, 2026

They don’t talk about shifter location and the owner looks to be in the upper 5’ range but is some good interior footage that shows the shifter location with a stock TKX shifter.

View: https://youtu.be/3OId8rmgYyo?si=iek6rE4bI-4wv-lF

AeroCoupe · Jun 7, 2026

They don’t talk about shifter location and the owner looks to be in the upper 5’ range but is some good interior footage that shows the shifter location with a stock TKX shifter.

View: https://youtu.be/3OId8rmgYyo?si=iek6rE4bI-4wv-lF

nicholase · Jun 7, 2026

fasterthangas said:
I have a MGW on my GForce and love it. I wanted one for the TKX but I need a handle that curves back towards me. They show only one handle that's straight up and down. I sit in a solid mounted Kirkey seat and I'm held in place with a 5 point harness.

I second calling them. I'm sure they have a substantial availability of handles.

I'm doing a TKX in my Fox and have the MGW shifter sitting on the bench. This is the comfort / oem handle.

fasterthangas · Jun 7, 2026

Great info guys! Thank you very much for the pics and details. I'll definitely post pics here once the TKX is installed. I've installed a Fox T5 into a SN95 and I had to cut around 5/8" out of the front of the lower shifter boot hole. The lower shifter boot plate still covered the hole and the upper boot worked fine.

fasterthangas · Monday at 10:40 AM

I had already emailed them and they got back to me today. All of the top loader handles work with the TKX shifter. I don't know why they don't advertise that on their site.

Drivetrain TKX Shifter Position Question

Active Member

Active Member

Active Member

lube between the nut and the face. I know my lubes

Active Member

lube between the nut and the face. I know my lubes

Active Member

Active Member

lube between the nut and the face. I know my lubes

Active Member

Stangnet Facilities Maint Tech... Er... Janitor

Drivetrain Post in thread 'Short throw shifter for Tremec TKX?'

Active Member

lube between the nut and the face. I know my lubes

wrap a little cheese around it and its a done

lube between the nut and the face. I know my lubes

lube between the nut and the face. I know my lubes

I lubed and pushed, until it was all the way in

Active Member

Active Member

Similar threads

Privacy & Transparency

Privacy & Transparency