• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

two different vac gauges, two different readings

  • Thread starter Thread starter luckythirteen13
  • Start date Start date Sep 11, 2005
L

luckythirteen13

New Member
Jul 19, 2005
648
0
0
Anaheim, CA
Sep 11, 2005
#1
  • Sep 11, 2005
  • #1
normally i run a vacuum gauge made by mallory ignition. it was brand new when i bought it. at idle it reads 20-22hg when not in gear. 18-20 when in gear. im going to put in a sc next week and im really excited about it so when my boost gauge came early, i decided to put it in and save myself 5 minutes worth of work later. anyways, its a brand new autometer sport-comp vac/boost gauge. at idle it reads 18-19 out of gear and in gear it reads 16-18. when the car is warm and in gear its usually 17hg. why the difference? one of them has to be wrong. i couldnt care less as long as its consistant. im only worried cause if the autometer is off on the vac, then will it be off for boost? it needs to be dead on for boost so i know what im running. how much "boost" can most people make with their lungs? i could blow in it to see what reading i get. what do you guys think?
 
D

Daggar

New Member
Jul 19, 2004
3,902
5
0
Sep 11, 2005
#2
  • Sep 11, 2005
  • #2
Are you using the exact same source for both gauges?
 
L

luckythirteen13

New Member
Jul 19, 2005
648
0
0
Anaheim, CA
Sep 11, 2005
#3
  • Sep 11, 2005
  • #3
yep, same source, same line, same fittings. all i do is change the gauge
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Sep 11, 2005
#4
  • Sep 11, 2005
  • #4
And are you sure both gauges have a tight seal on the nipple. Back in the day, I had one gauge with a large nipple and it was a PITA to keep sealed up.

I also am not sure about the 'in gear' part - manifold vac is not dependant upon being in gear.
Said overly crudely: Manifold vac is inversely proportionate to how far the gas pedal is pushed.

Good luck.
 
L

luckythirteen13

New Member
Jul 19, 2005
648
0
0
Anaheim, CA
Sep 11, 2005
#5
  • Sep 11, 2005
  • #5
both use a compression fitting to hold the very thin plastic line to the back of the gauge. they have a good seal. what i mean by in gear is, i have an aod. when it park, the idle is higher then when the trans is in drive and i have my foot on the brake. guess that doesnt matter, long story short, the autometer is reading lower by about 2-3hg
 
D

Daggar

New Member
Jul 19, 2004
3,902
5
0
Sep 11, 2005
#6
  • Sep 11, 2005
  • #6
Well... that about covers it then. One gauge reads different than the other. lol

Where shall we send the bill?
 
L

luckythirteen13

New Member
Jul 19, 2005
648
0
0
Anaheim, CA
Sep 11, 2005
#7
  • Sep 11, 2005
  • #7
well i went back and pulled the gauge off. i cut the tip of the plastic hose off including the compression fitting. i put a new compression ring on the freshly cut hose, and put thread tape on everything. at idle the gauge reads 19hg, just under 20. is this about right?
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Sep 11, 2005
#8
  • Sep 11, 2005
  • #8
Yep, 16-22" hg is good to go IMHO.

Also with the 'in gear' thing, if the reading is slightly lower with the brake applied, it might be the booster's affect on things.

Good luck.
 
D

Daggar

New Member
Jul 19, 2004
3,902
5
0
Sep 11, 2005
#9
  • Sep 11, 2005
  • #9
Hiss--

There is an idle or rather "load" cahnge in the EEC When shifting out of park or neutral. It would account for the vac change as well. I've seen reference to it in the TwEECer forums. There is a scaler in the EEC just for that as well as an EEC controlled time delay to go along with it.

It's partly, to ensure that the motor doesn't die when shifting into gear.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Sep 11, 2005
#10
  • Sep 11, 2005
  • #10
Daggar said:
Hiss--

There is an idle or rather "load" cahnge in the EEC When shifting out of park or neutral. It would account for the vac change as well. I've seen reference to it in the TwEECer forums. There is a scaler in the EEC just for that as well as an EEC controlled time delay to go along with it.

It's partly, to ensure that the motor doesn't die when shifting into gear.
Click to expand...
Ah so. Why thank you old wise one. I try to learn something every day. Most of the time I forget it by the next day, but.......

BTW, why do you read about scalar values for autos?
 
D

Daggar

New Member
Jul 19, 2004
3,902
5
0
Sep 11, 2005
#11
  • Sep 11, 2005
  • #11
HISSIN50 said:
Ah so. Why thank you old wise one. I try to learn something every day. Most of the time I forget it by the next day, but.......

BTW, why do you read about scalar values for autos?
Click to expand...

I don't go looking for them. lol The TwEECer forums are not too different from these. I fell onto it a time or two while reading up something else.
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Sep 12, 2005
#12
  • Sep 12, 2005
  • #12
Daggar said:
I don't go looking for them. lol The TwEECer forums are not too different from these. I fell onto it a time or two while reading up something else.
Click to expand...
I figured as much - I was just playing. I know all sorts of stuff I dont want to know about just from reading forums.

I have lurked a bit myself on some of the TwEECer sites. If I stay, I will end up getting one. (cant spend the funds on one, otherwise I would love it).
 
You must log in or register to reply here.

Similar threads

Forced Induction Bypass valve backwards?
  • Dontknowchit
  • Jun 25, 2025
  • Fox 5.0 Mustang Tech
Replies
3
Views
483
Fox 5.0 Mustang Tech Jun 29, 2025
JD1964
Engine Random Misfire at idle.
  • Gulftown980x
  • Jul 29, 2026
  • SN95 4.6L Mustang Tech
Replies
11
Views
613
SN95 4.6L Mustang Tech Jul 31, 2026
squeak93
Fox Fuel Pump Issues After Replacement/Upgrade
  • Ryu
  • Jun 23, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
24
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 13, 2026
Ryu
Electrical Innovate PSB-1 is DOA? Am I an idiot? All plausable. Please Help
  • Dontknowchit
  • Apr 26, 2025
  • Fox 5.0 Mustang Tech
Replies
1
Views
681
Fox 5.0 Mustang Tech Apr 26, 2025
Dontknowchit
X
Free VE Table Corrections — Drop Your MSQ and a Datalog, I'll Do the Rest
  • X-cam34
  • Apr 12, 2026
  • Digital Self-tuning Forum
  • 2 3
Replies
49
Views
2K
Digital Self-tuning Forum Aug 26, 2026
X-cam34
X
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?