• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Understanding gauges in my new Mustang

  • Thread starter Thread starter MadMatt5oh
  • Start date Start date Jan 4, 2004

MadMatt5oh

Member
Jan 10, 2003
441
0
16
St Paul, MN
Jan 4, 2004
#1
  • Jan 4, 2004
  • #1
Ok guys, I recently bought my first stang. I have some questions regarding my gauges. Here goes....

1. My temperature gauge in my orginal cluster doesnt work. How do I restore it?

2. I do have a set of aftermarket VDO gauges circa 1988 or so (was the shyt back in those days).

The first gauge is a vacuum gauge. It reads a steady 20 psi on idle. But what is this really for?

The secound is an oil pressure gauge which shows the pressure to be about 15 - 20 psi above the stock one in the original cluster.

The 3rd is a Transmission temperature gauge. Is it possible that my orginal equipment has been rerouted to the T5's temperature instead of my engine's coolant temperature?

What should I do with these gauges? Leave them? How do I fix the coolant temp gauge?
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Jan 5, 2004
#2
  • Jan 5, 2004
  • #2
for the temp, check the sender wire. the sender is on the top front on the lower intake. find the dizzy, and look to the driver side of it. you will see a sender with one wire connecting to it. IIRC, you can remove the wire and ground it. this should make the gauge read fully hot. someone should say yeah or nay to this, as i cant remember if it shows fully hot or fully cold when grounded (i think it is fully hot). this would tell you if the gauge itself works. go from there with a new sender, wire, gauge, etc. the stock gauge sucks, so just use an aftermarket, IMO (i am one though that hates dead gauges). i run both, and the stocker never goes above half, while the aftermarket shows im getting too hot.

the oil pressure gauges suck and typically read low. so you are right on par. a new stock sender may or may not help. i rely on the aftermarket gauge.

if your 88 is still speed density, i like the vac gauge. i run one in mine too. since vacuum is so critical to their running right, i like to monitor the vac. useless otherwise. LOL.

dont know about the trans thing. just look for a sender on it. most people dont run one, but some have (IIRC, Michael Yount does).
good luck.
 

MadMatt5oh

Member
Jan 10, 2003
441
0
16
St Paul, MN
Jan 5, 2004
#3
  • Jan 5, 2004
  • #3
OK, cool, Thanks Hissin' youre alright bro. I think I have enough to nibble on for a while because is so fawcking cold I wont bother to look! -10 below all week!

So, thanks for the location of the coolant temp sensor. I take it the T5 has a custom sending unit? I'll pm Michael Yount. I've seen him around here for a while.

Yeppers, My 88's basically stock so it still has the original SD equipment. God I love my car
 

HISSIN50

"How long does it take to get help in here?
15 Year Member
Nov 29, 1999
31,179
34
129
Jan 5, 2004
#4
  • Jan 5, 2004
  • #4
MadMatt5oh said:
OK, cool, Thanks Hissin' youre alright bro. I think I have enough to nibble on for a while because is so fawcking cold I wont bother to look! -10 below all week!

So, thanks for the location of the coolant temp sensor. I take it the T5 has a custom sending unit? I'll pm Michael Yount. I've seen him around here for a while.

Yeppers, My 88's basically stock so it still has the original SD equipment. God I love my car
Click to expand...
i hear you about the cold. lived in alaska for too long, myself.

if there is something for monitoring temp on the T5, it most certainly is custom. i would think it would be very easy to spot. the gear portion of the box is small and there aint much around (especially with one wire). you would see it tapped in there (or replacing the drain plug?). imagine it will be awhile till you lay under and look. LOL.

good luck.
 
You must log in or register to reply here.

Similar threads

G
2005 Mustang GT AC cycling on and off every minute
  • GeorgeSwadling
  • Jul 12, 2025
  • 2005 - 2009 Specific Tech
Replies
0
Views
230
2005 - 2009 Specific Tech Jul 12, 2025
GeorgeSwadling
G
H
Ongoing Battle With Hydraulic Lifters
  • hailer06
  • Jun 8, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
291
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 9, 2026
Noobz347
Electrical 5.0 Resto Gauge Cluster Fuel Ohms
  • sav22rem22
  • Dec 31, 2023
  • Fox 5.0 Mustang Tech
Replies
5
Views
2K
Fox 5.0 Mustang Tech Mar 6, 2024
1everett1
1
Engine I think I broke my coolant temp gauge
  • AnthonyA1234
  • May 15, 2023
  • Fox 5.0 Mustang Tech
  • 2 3
Replies
45
Views
5K
Fox 5.0 Mustang Tech Aug 31, 2023
AeroCoupe
K
Engine 2000 Mustang GT - Fuel issue post-blown spark plug repair
  • kenster1092
  • Feb 26, 2026
  • SN95 4.6L Mustang Tech
Replies
4
Views
351
SN95 4.6L Mustang Tech Mar 10, 2026
kenster1092
K
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?