• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Vent tube?

  • Thread starter Thread starter Djstorm100
  • Start date Start date Nov 24, 2007
D

Djstorm100

Member
Aug 5, 2007
109
0
16
Nov 24, 2007
#1
  • Nov 24, 2007
  • #1
The vaccum hose that is on the oil cap where should this go? If you have a vortech sc? I looked on there and it said to put it on the intake box cover that vortec gives you. Theres a check valve that only allows air to come out the tube and not back in to the tube (and in to the motor) I'm kinda thinking that this is where I'm getting a vaccum leak from. Since I only pull 3-4 on vaccum side. Needless to say yesterday comeing home the guage when tto 21 vaccum. I turned the car off and then back on and it wouldnt read back to 21 one again. I re did all the lines (didnt replace them) but make them shorter and the shortest possible path. Also theres a vaccum line that goes from the intake manifold and down in between the heads and the smog pump/ alternator, what is the purpose of the line and can I just take it off and cap the nipple on the intake manifold?
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,372
18,120
224
Massachusetts
Nov 24, 2007
#2
  • Nov 24, 2007
  • #2
Normally, it connects from the oil fill neck to the throttle body.

The other vaccum line you are talking about goes to the charcoal canister and helps draw gas vapors through the activated charcoal and into the engine for combustion. You should not remove this line
 
D

Djstorm100

Member
Aug 5, 2007
109
0
16
Nov 25, 2007
#3
  • Nov 25, 2007
  • #3
anyone else?
 

PUNISHER RACING

Active Member
Aug 27, 2007
1,124
0
36
FORD CITY, PA.
Nov 25, 2007
#4
  • Nov 25, 2007
  • #4
block it off and run an open element breather, that blowby will contaminate your intake charge and cause detonation it will also help your smooth your idle out.
 
You must log in or register to reply here.

Similar threads

J
1990 fox starts on starting fluid only
  • Jfox
  • May 14, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
9
Views
396
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- May 15, 2026
AeroCoupe
Electrical problem plug in the drivers kick panel
  • Mindseye007
  • Aug 16, 2026
  • Fox 5.0 Mustang Tech
Replies
3
Views
242
Fox 5.0 Mustang Tech Aug 16, 2026
Mindseye007
Forced Induction Bypass valve backwards?
  • Dontknowchit
  • Jun 25, 2025
  • Fox 5.0 Mustang Tech
Replies
3
Views
491
Fox 5.0 Mustang Tech Jun 29, 2025
JD1964
D
Question about EGR valve, replacement, and a part on the valve.
  • DPP
  • May 9, 2026
  • SN95 V6 Mustang Tech
Replies
1
Views
271
SN95 V6 Mustang Tech May 23, 2026
DPP
D
M
  • Locked
2001 evap core tube support
  • mnky99
  • Sep 4, 2025
  • SN95 V6 Mustang Tech
Replies
4
Views
464
SN95 V6 Mustang Tech Sep 5, 2025
mnky99
M
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?