• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

Weird rocker adjustment?

  • Thread starter Thread starter RACEME
  • Start date Start date Jun 15, 2007
R

RACEME

Member
Jun 10, 2002
24
0
7
Jun 15, 2007
#1
  • Jun 15, 2007
  • #1
I got my 95 mustang running last night but it was not the normal setup to do it.

I have the dart pro 1 alum 170 cc (13111181) heads on a factory oem 93 mustang shortblock with a trickflow stage 1 cam (.510 +\-) and factory ford hyd. roller lifters. I am also running Comp. Cams 1.6 silver roller rockers and 6.5" hardened pushrods.

I adjusted the rockers like this. I spin the pushrod with my fingers while tighting the rocker nut until there is tension on the pushrod and I almost can not spin it. Then I crank the nut about 3/4 turn more and lock the set screw.

At first the motor would not start. After checking all the normal stuff (fuel, spark, air, dist. position ect) I put my compression tester in the spark plug hole and had no compression in any cylinder. It turns out that the rocker was holding the valve open slightly all the time. I had to back the adjusting nut off all the way and only give it 1/8th turn or less of preload.

It starts and runs like this with no strange ticking or anything, but I am still nervous about the small amount of preload I have on the lifters.

Has anyone ran into this? Could the springs be weak? (heads came assembled)
I have not checked the spring pressures, and I don't think I have the tools to do it. It is like my factory lifters have an ego problem?

Thanks...Tim
 

millhouse

Founding Member
May 14, 2002
1,985
0
46
Simpsonville, SC
Jun 15, 2007
#2
  • Jun 15, 2007
  • #2
It sounds like your adjusting the preload too tight. When your feeling for pre-load you want the point at which there is "barely" any resistance on the pushrod and then turn the 3/4. If it becomes in the least bit difficult to spin you have gone to far. If it were me I'd go back and re-adjust them for peace of mind.
 

GT_Rich

Member
Dec 11, 2005
172
0
17
North Canton, OH
Jun 15, 2007
#3
  • Jun 15, 2007
  • #3
Yeap, what he ^ said. You could also adjust them running since the car now runs for you. If you search my username you'll find a few posts where I suggested this and the details.
 
You must log in or register to reply here.

Similar threads

K
Engine Gt40p vs 180 procomp
  • Kleinjj27
  • Oct 27, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
520
Fox 5.0 Mustang Tech Nov 3, 2026
Kleinjj27
K
G
Engine Pushrod Length Question
  • germain101
  • Sep 22, 2025
  • Fox 5.0 Mustang Tech
Replies
12
Views
756
Fox 5.0 Mustang Tech Sep 25, 2025
Noobz347
1
Crank no start on a turbo and cammed pushrod 5.0
  • 1630stri
  • Sep 2, 2026
  • Digital Self-tuning Forum
Replies
2
Views
214
Digital Self-tuning Forum Sep 16, 2026
Qtrhrse23
H
Ongoing Battle With Hydraulic Lifters
  • hailer06
  • Jun 8, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
617
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Jun 9, 2026
Noobz347
Engine Finishing up 331 build
  • RedFury5.0
  • Mar 21, 2025
  • Fox 5.0 Mustang Tech
Replies
9
Views
769
Fox 5.0 Mustang Tech Apr 20, 2025
RedFury5.0
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?