• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-

who is using sn95 springs?

  • Thread starter Thread starter SVO1
  • Start date Start date Apr 4, 2004

SVO1

Lord of The somethin' somethin' somethin', hell, I
Oct 25, 1999
4,592
1
0
Lord of uh, hmm what was it again?
Apr 4, 2004
#1
  • Apr 4, 2004
  • #1
From what I could find I think Bhuff, and not sure who else.
How much trimming did you do?
I have line on a dirt cheap set of c springs for an sn95 and I am thinking they would work well in my 87
Thanks for any insight!
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,243
17,924
224
Massachusetts
Apr 4, 2004
#2
  • Apr 4, 2004
  • #2
C springs are not SN95 specific. They are actually 79-04 Springs and will work in all Mustangs.

I have a set in my '88
 

SVO1

Lord of The somethin' somethin' somethin', hell, I
Oct 25, 1999
4,592
1
0
Lord of uh, hmm what was it again?
Apr 4, 2004
#3
  • Apr 4, 2004
  • #3
Mike- Thanks!
Was thinking that but wa snot 100%.
I just know he said they were a gift for his 95 but he dedcided they were too stiff and took them out
So I think i gotta call him tomorrow !
 

chaka

Founding Member
Mar 1, 2002
1,342
0
0
Boston, MA
Apr 4, 2004
#4
  • Apr 4, 2004
  • #4
I have them in my 79. it is BB'd with one coil cut in front I could place one finger between the fender and tire. Tall in the rear. Haven't cut any coils out back yet.
 

bhuff30

Founding Member
Dec 11, 2001
6,037
35
129
Olathe KS
Apr 4, 2004
#5
  • Apr 4, 2004
  • #5
SVO1 said:
Mike- Thanks!
Was thinking that but wa snot 100%.
I just know he said they were a gift for his 95 but he dedcided they were too stiff and took them out
So I think i gotta call him tomorrow !
Click to expand...
yup, they shuold work. Brantley is running C springs. I know that Wish cut them down some to lower it a little, but I don't know how much. Expect a harsh ride.
 

SVO1

Lord of The somethin' somethin' somethin', hell, I
Oct 25, 1999
4,592
1
0
Lord of uh, hmm what was it again?
Apr 4, 2004
#6
  • Apr 4, 2004
  • #6
Harsh is good Give all the ladies a back ache riding with me!

Seriously tho, I hope to jack the car up a bit, the stock springs are so worn the car sits about 2 3/4 lower than stock, and it handles like a wet bag of ****!
(plus unless you drive it on blocks you can not get a jack under it)


Figure I should get my baby back together right so we can start a new life out together.
 

Lx89Stang05

Founding Member
Oct 18, 2002
1,005
0
0
S.E. Mass
Apr 4, 2004
#7
  • Apr 4, 2004
  • #7
i have 94 corba springs, and there cut, people say you get a hard ride but i like them stiff since i autocross,i wish they where harder
 

Red_LX

I’m not much help unless you’re looking for ****!
Founding Member
Nov 29, 1999
5,896
73
129
Morgantown, WV...where couches meet their doom
Apr 4, 2004
#8
  • Apr 4, 2004
  • #8
I got some SN95 springs for my Thunderbird....just haven't put em on yet.

As a side note, on my '90 I put 5.0 springs in the front and '84 TC springs in the rear. Musta lifted the car at least 2 inches
 

mr_woodster

Active Member
Jul 28, 2003
1,314
0
36
Riverside, CA
Apr 5, 2004
#9
  • Apr 5, 2004
  • #9
<center>2" , i laugh...try this one on for size...

 

Red_LX

I’m not much help unless you’re looking for ****!
Founding Member
Nov 29, 1999
5,896
73
129
Morgantown, WV...where couches meet their doom
Apr 5, 2004
#10
  • Apr 5, 2004
  • #10
mr_woodster said:
<center>2" , i laugh...try this one on for size...

Click to expand...


Some guy out around here had a '70s Corvette just like that. Primer black and sitting on a Blazer frame with 38's or 39.5's under it.
 

nomuffler

Member
Aug 20, 2003
330
0
16
Awash in a sea of decedant luxury and meaningless
Apr 5, 2004
#11
  • Apr 5, 2004
  • #11
I had Eibach sportlines that came off my dad's '00 Gt, it went down an inch with no cutting. They work great, the rear shocks from his car worked great as well.
 
You must log in or register to reply here.

Similar threads

0
V6 to V8 Swap info
  • 02_2v_Curtis
  • Jan 11, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
0
Views
671
1996 - 2004 SN95 Mustang -General/Talk- Jan 11, 2026
02_2v_Curtis
0
B
Paint in engine bay questions
  • B0udreaux
  • Feb 26, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
8
Views
273
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Feb 27, 2026
AeroCoupe
B
water pump installation questions
  • B0udreaux
  • Feb 5, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • 2
Replies
38
Views
2K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Feb 28, 2026
General karthief
Engine Suggestions on an engine rebuild. Stock cam/GT40Ps or aftermarket on both for a fun weekend driver?
  • MadSquirrelTech
  • Apr 28, 2026
  • Fox 5.0 Mustang Tech
  • 2
Replies
23
Views
752
Fox 5.0 Mustang Tech May 7, 2026
MadSquirrelTech
SN95 Desktop 363 Engine Combination - Looking for input
  • WhiteCobra95
  • Sep 8, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
11
Views
1K
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 6, 2025
Habu135
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?