mass air conversion

nasty5pt0

New Member
Aug 5, 2004
4
0
0
hey guys, i have been researching all over the forum about everyones methods & problems for doin the conversion... i have an 88 gt, and i converted it to mass air. i got the complete engine harness and computer out of an 89 i believe it was. everything was all well and good until i put the cam in (tfs stage1), 1.7 rockers, 30lb injectors and 30lb mass air meter. the car surges, stalls and misses. will not stay running. timing is on (about 14* or so), i got about 43lb's of fuel pressure which stays consistent. i have good vacuum. cleaned the egr out.new tps sensor. new iac valve.... just a little frustrated at this point and any help would be of great appreciation. i am just curious if there is something i have to change in the harness on the dash side of the harness??? it almost feels like its an electrical failure or sensor because the problem is so intermittent. thanks for the help in advance everyone.
 
No heads?? Injectors are wayyy too big. Get a set of 19s and and borrow a stock MAF to see if it fixes it. PM me and I'll give you a stock MAF and a set of newer 19#ers for cheap. Hopefully that'll fix it. I'd save the 30 #ers for a nice set of heads!
 
yeah stock heads.... i dont have the stock mass air meter or injectors either.... u think it would really make a difference??? before i put the cam in, the car ran fine w/ the 30lbers....

heres the deal: it wont stay running unless i keep feathering the gas, once i let 1st out it will pull OK ( still missin a bit) and if i mash it sometimes it will pin me in the seat but then it will fall flat on its face out of no where like i turned the key off... and it will come back on , then off... its the weirdest thing.. i had a couple of friends look at it as well, they seem to think is has to do w/ the computer.. im not sure; if you guys think its to injectors/ mass air meter.. then maybe ill try and dig something up out of the junk yard and try that, as i already chucked all my stock parts....

also i already threw the old speed density harness out, sorry brotha!!! all i have is a mass air harness out of a 91 i think but it was no use to me because it was out of a car w/ air bags
 
im suprised no one's said this yet but pull the codes. i was having this problem up until the other day. i saw you said you got a new iac. a lot of aftermarket iac's require you to flip them upside down in order to work properly. i put a new mass air meter on my car and put my bbk cai back on, car was surging pretty bad, would stall when i came to a stop. i have an aftermarket iac from autozone. i flipped it upside down, surging problem solved. it idle's PERFECT now.
 
Well I never run 43 lbs of fuel pressure either. that could also be a possible remedy. Make sure the car is not running and bring it down to 38-40 lbs and see what that does for ya. I know 30lbers are big for your combo, but it doesnt help when you forcefeed the fuel that way. Give it a shot...
 
thanks alot for all the input guys, i really appreciate it.... when i get outa work ill mess around with it tonight.... one question though, with the wiring.. i was reading the one thread that says you have to tap into the vss wire and the fuel pump wire and run it into the computer.... do i still need to do that even tho i changed the whole harness out w/ a true mass air harness?
 
thanks alot for all the input guys, i really appreciate it.... when i get outa work ill mess around with it tonight.... one question though, with the wiring.. i was reading the one thread that says you have to tap into the vss wire and the fuel pump wire and run it into the computer.... do i still need to do that even tho i changed the whole harness out w/ a true mass air harness?

No. It is not necessary when you use a harness from a Mass Air car.