Progress Thread Low Mile 89 GT Restomod - More cut and buffing along with some distractions

We decided to go with hood struts instead of a prop rod. I pieced together something starting with a kit from a BRZ off Temu. The kit was about $30 CDN and included mounting brackets and 11" (extended) struts. I purchased an additional pair of 15" struts rated at 100lbs ($48 CDN) as the originals are much lighter capacity.

1000013261.webp
The Temu kit with the 15" strut at the top.

Had to drill out the upper bracket for an additional hole to attach to the top hood hinge bolt. The lower section near the middle hole needs to be ground back a little bit (1/8-1/4") and I then welded up the middle hole for strength followed by a quick respray of semi-gloss Tremclad paint.
1000013262.webp

The lower bracket comes with an offset formed in it. I needed to straighten it back out to fit where I wanted it.
1000013263.webp

Install is in the top hinge bolt and the lower attached to the middle fender bolt.
1000013267.webp

All finished it works well. It is not bad to lower and has almost no resistance trying to push up for the last 3-4" before fully closed. The last pic is with a prop rod mocked up to show it doesn't open as far as the prop rod would hold it, but I'm pretty happy with it. We will see how it is longer term with use.
1000013266.webp 1000013265.webp
 
Though not going on my son's car, but I picked this up last summer and decided to clean it up/repair it a bit.
20260309_210717.webp 20260309_210648.webp


A previous owner had the thought of enlarging the inlet - probably thinking it was needed for a 75 or 80mm TB.
20260309_211203.webp 20260309_211215.webp 1000012999.webp 1000013001.webp

1000013003.webp 1000013002.webp

They bored a nice straight hole that fits a 3" piece of exhaust or intercooler tube inside (perfectly), but broke through the cast near the throttle body mount.
Damn, that's one rare ass intake to, smooth side production intake limited to first 500 or so 93 cobras.
 
I picked up a replacement pair of door moldings as the originals were a bit beat up.

20240916_121913.webp
Passenger side curled down toward thee ground at the front.

20260916_202605.webp 20260916_202554.webp
Cleaned up the old adhesive from the rear.

Last couple of bits got painted red. The door moldings and one of the side skirt pieces.

20260918_174316.webp 20260918_183243.webp 20260918_183309.webp
 
  • Like
Reactions: 85GT4V
With the red done, its time to focus on getting some trim painted.

20260919_090237.webp 20260919_090244.webp 20260919_090255.webp 20260919_090304.webp

With the masking removed...

20260919_183151.webp 20260919_183155.webp


Got the wheels and tires mounted up...
2caba0a3-3331-4bc9-aad2-503a80ce37e7.webp 20260919_193203.webp
Couldn't resist putting one of the rear tires on to see how it looks.

Refinished one of my spare sets of quarter windows as the original passenger side piece had some kind of fading or water stain under the glass, on top of the black background coating.
20260919_231646.webp 20260919_231858.webp

Then temporary installed (so they don't get damaged sitting around the shop).
20260920_082131.webp 20260920_082137.webp
 
Pulled the car outside to give it a first bath post painting to clean the dust off before a cut and buff.

1000014441.webp 1000014440.webp 1000014435.webp

Then some post wash pics in the sun.

1000014428.webp 1000014430.webp 1000014431.webp 1000014432.webp

Roof and hood are pretty good but still some trash that needs correcting.

1000014437.webp 1000014438.webp 1000014439.webp

I had a bunch of runs in the clear on the hood. You can see some of the areas where I scraped with a razor blade. Still more work and I may have to re-clear the hood.
 
  • Like
Reactions: gkomo and 85GT4V
I wanted to get the cut and buff out of the way so that I could permanently install the 1/4 windows and door seals and trim.

I first tried buffing only with a series of denim pads and a 3M Finesse It - Finishing Material compound.

1000014443.webp 1000014444.webp 1000014445.webp 1000014446.webp

It definitely improved the orange peel but the reflections were not good enough in my opinion in a bunch of areas so I decided to sand with 1500, 2000 and 3000 before re-buffing with the denim pads.

1000014447.webp 1000014448.webp 1000014449.webp

1000014458.webp

I did half the roof and the driver side fender, door and quarter panel. Still need to do the rest.

1000014459.webp

I got the hood sanded with 1500, but will probably still re-clear it as when I was scraping the runs I had one where the bubble at the end of the run popped completely off and it looks like in that small area all the clear came off. So probably a re-sand with 800 and two more coats of clear - next trip at the end of October.

I also got the door handles and upper door/window trim painted so they will be ready to go on once finished with the buffing.
 
Was down working on the car again this past week. Didn't get as much done as I was hoping. I did repair/re-clear the hood and finished the color sanding on the passenger side and hood (after re-clear). I got the first round of buffing done on the hood and top of passenger fender and then ran out of time.

1000014536.webp

I have also sanded the front (attaches to front bumper) and rear side skirts (between door and rear wheel). Still need to sand the remainder of side skirts, hatch and spoiler and both bumpers.

My son made a decision (finally) on emblem colors - the choice was factory blue background or the black background ones. He picked the black ones. He also decided on black 5.0 badges. We are going with a black (Canadian) Cobra sticker on the hatch as well. Do you sense the red with black theme here.

Part of the reason for the lack of progress was I had to pick up a couple new/future projects.

The first is a 2012 Kona blue V6 auto with the Premium and Pony packages. It will either be a flip or a future DD. We will see. It needs some paint touch ups, a little bodywork and brakes and tires for a safety.
1000014501.webp

The second pick up will be the basis for my next foxbody build.
1000014505.webp 1000014508.webp 1000014509.webp 1000014512.webp

1000014510.webp 1000014511.webp 1000014517.webp

1000014515.webp 1000014516.webp

It is an 89 GT, original 5spd and AC car, odometer shows 159k kms. It is a complete car, less drivetrain, hood, front bumper, tail lights and ECU. Rust wise it appears excellent. The passenger side shock tower/frame rail has had something done to it as seen by the unusual patch covering seen in pic, but not sure how extensive (will probably open it up and re-address if needed). It has had a front impact at some point in its life as there is a bulge in the frame rails in front of both shock towers and passenger front apron is VERY wavy (someone tried straightening it).

The plan with this one is a color change to blue (Sonic, Viper, Velocity/Lightning - not sure yet which one). Coyote swap with 5 spd manual (I have both TR3650 and T45 trans). I have an extra 8.8 with 31 spline fox length axles and 3.55 gears. There will be some subtle exterior mods but will keep with the GT/Cobra theme. A full color change will happen on the interior and will retain a OEM look and feel (mostly).

Probably not moving this forward in any way until late summer or fall 2027. I will do its own build thread when this gets started.
 
Last edited: