Search results

  1. 1

    PMS Tuning basics

    Hello all, I have been in the dessert for some time. Now I am back and recently purchased a used PMS tuner for the Stang. I am interested in setting up two tunes. One for N/A and one for the track when I spray Nitrous. I have not ever used one of these tuners. I here the PMS is easy to...
  2. 1

    Dumb Question....Checking Vacuum

    I am having idle problems, and suspect a vacuum leak. I purchased a the vac pump with gauge from O reily. Heres the dumb question. Where should I connect it to see overall vac the engine is producing. I uderstand how to apply pressure/vac to various places and see if it holds in order to...
  3. 1

    How do I fix TB Whistle...

    I recently installed a PP 75MM TB and EGR Spacer along with a C&L 76MM MAF and power pipe. I have not had much time to mess with the car until today. I also have a LC-1 Wideband AFR monitor hooked up. When I start the car is idles very rough which I believe to be due to the TPS and Idle...
  4. 1

    What are these screws for?

    I recently replace the throotle body, egr, maf, and pipe on my coupe. when I was changing over the throttle body, and installed a new IAC valve I noticed the small plate in between. The alan screws were all the way closed. I opened them a little. Now when I started the car it Idles at about...
  5. 1

    Best Ignition for the Stang

    Hello all. I am interested in upgrading the ignition on my coupe. I have an MSD Blaster coil and MSD 9mm wires. I am interested in a new distributer, and box. I am curious as to the best choice. Can I use a digital ignition? I know most of the ones I see around have an MSD 6AL. Is there...
  6. 1

    Fuel Pressure Bleeding Down

    I recently installed a TFS Street Upper/Lower, and while I was doing the swap put a BBK adj regulator on just to do it. I also cleaned all the injectors and replaced all the o-rings. I am having trouble adjusting it. It says to cap the vac line, and set the pressure. Prior to the swap you...
  7. 1

    Cam Question

    I have a 90 Coupe with that is a conversion car 4cyl to 302. I got the motor out of a wrecked 90 LX, AOD car. It only has 45 k on it. My question is this...I know there is a difference between the cams for an AOD, and for a 5-Speed car. What are they, and could this be holding my car back...
  8. 1

    Buying a Throttle Body.....opinions.....

    I am going to buy a throttle body and egr spacer for my car. I just got a new TFS Street upper/lower. I was thinking a 70MM would be right for me, and am looking at all the brands available. BBK, Edelbrock, Accufab, Professional Products. I see the P/P ones are a lot cheaper. Does anyone...
  9. 1

    Help...Need Trick Flow Intake Part #s

    I have been talking to this guy in SC about buying a Trick flow upper and lower. I live in GA. He told me the part #s were Upper- TFS-EFISBF01 I may have the EFI and the SBF switched not sure. Lower- TFS-EFISBFLP I was in Lowe's when he called and couldn't write it down I...
  10. 1

    Trick Flow Track Heat..Too Big??????

    I found a good deal on a Trick flow Track Heat intake, and I am wondering if it is too much for my car. I plan on putting AFR heads on eventually, and I hate buying stuff twice. Current mods in Sig. I am also considering a new 70MM TB, and bigger mass air meter. I do not have the money to do...
  11. 1

    31 Spline Axles

    I have a dumb axle question. I know that my car comes with 28 spline axles stock. I would like to put a set of Superior axles in. I was looking at the 31 spline ones that are 3/4 inch wider than stock. This would aid in fitting some bigger tires and be an improvement over stock. What is...
  12. 1

    Explorer hesitates with light acceleration

    Hello all, :Word: I have a 96' Explorer with a 5.0. It recently started to hesitate. I has an AOD in it. It also has 195k miles on it. The best way to describe it is that it hesitates with minimal throttle. When it starts to do it if you accelerate to half throttle it almost stops. It...
  13. 1

    Looking for front bumper

    Last year at the Fun Ford Weekend I seen a couple 87-93 LX's with a front bumper that I am interested in. I looks similar to the lower part of a GT bumper but the Fog Lights are mounted in the middle instead of the outside. Anyone know of these and where to find them. I am searching through...
  14. 1

    Torque Box Kits

    Any body know where to get a decent torque box kit and a decent price. I have looked on Ebay, but there is not a whole lot there. I have heard bad things about Dynamic Racing so I do not want to buy from them. Any suggestions?
  15. 1

    Car shuts off with air on

    I returned home last week after my deployment, and have drove my car twice since then. Yesterday I was preparing to turn into my subdivision and the damn thing just shut off. It started right back up, and I drove around some more to see WTF. It only does it when the AC is on, deceleration...
  16. 1

    Question about an Anti-Roll Bar

    I am considering installing an Anti-Roll bar on my coupe, and want some info. Do's Don'ts, benefits, etc. How does it affect street drivability?
  17. 1

    Educate me on Rear Axles

    I am going to replace the rear axles in my car, primarly as a safety concern. I am researching the different choices. Best I can tell, stonger axles with C-clip eleminators is the way to go, but what spline? Brand? I was also considering going a little longer than stock in order to...
  18. 1

    Looking for high 11's

    :Word: I am currently deployed, and looking to do some changes when I get home. I have about $1500 to spend. My sig states most of my mods. Just before I left I blew a head gasket, and repaired it. Below is a complete breakdown of my car. Where should the money go first? Ported stock...
  19. 1

    Wheel spacers with Weld Draglites

    I recently purchased some draglites and put them on the car. In order to prevent them from rubbing I put 1/4 spacers on them. It is still a 4 lug car. I always torque the wheels on using a torque wrench set at 90ftlbs. I am wondering what your thoughts are on this setup?
  20. 1

    Timing Question

    I recently removed the heads off my car due to a blown head gasket. During the install I rotated the crank in order to install the rockers. I am not sure if it is at TDC and I am certain that it is not in the same posion that it was when I removed the distributer. What is my best cours of...
Top Bottom
Back
Forums
Menu