Search results

  1. B

    What happens when..

    My buddy has a 03 GT he is getting ready to sell, but when he went to put the factory tune back in he found that his Predator is lost. The non- performance tune was in with a couple things adjusted. He would like to know if he could go in with another predator (or any other programmer)and...
  2. B

    How much should I sell my car for?

    Yeah I know, sucks. But seriously, I'm not sure how much I should ask for my car. It's a 2001 GT with the bullit style rims, all options except sunroof, electric green, 23,000 miles and the following mods: -PMAS MAF w/ big fancy filter -steeda boost-a-pipe -Paxton novi 1000 -Vortech...
  3. B

    injectors to big?

    I am planning on putting a paxton novi 1000 with a Anderson powerpipe on my GT, and was looking at a used set of injectors. Would 50# injectors be too much if I plan on using the pulley that comes with the kit? I know most poeple use 42# injectors, but I would rather get these used ones if I...
  4. B

    Converter install problems

    Yeah, I put my stock torque converter back in recently and when I tried to start the car, it had a hard time turning over and made some friction sounds when it was turning. So I shut the car off right away and tried to crank the engine by hand, it didnt budge. The transmission was flush with...
  5. B

    Need automatic transmission help

    So a week or two ago I got this PA valvebody in. When the overdrive was on and I tried to give it a decent amount of throttle, the car would rev up like it was in neutral. But at about 4200 rpm it would catch and the car would take of. So I called PA and told them about, and they said to send...
  6. B

    Need seperator plate hole diagram

    I was going to drill holes in my seperator plate today (for j-mod) but the TCCOA site wont show me any pictures. If anybody has something that shows which holes on the seperator plate I need to drill, it would be great if they could send them to me.
  7. B

    PA valve body installed, serious problems...

    Yeah..... :nonono: My o/d light comes on about 15 seconds after i start it, and when I shift through the gears, its not going into the right gear. Sometimes if I put it in reverse it wont move, but sometimes it will roll forward slowly? For the love of god please help me!!!!!!!!!!! I'll...
  8. B

    Filter fell out when I took out valve body, Need to know where it goes!!!!

    The question is the headline! Its about to get dark and I'm doing this in a parking lot!!!! nedd help ASAP!!!!!!!!!!!!!!!!!!!!!!!!!!
  9. B

    Need valve body help!!!

    I got my PA street strip VB and I would like to put it in today. My problem: It came with four springs and crappy directions for installing them on the 1-2 and 2-3 "accumulator pistons". Could some one please explain where the hell the pistons are? :shrug: are they in the VB they sent or in...
  10. B

    Ford front liscense plate legal in Wisconsin?

    The title says it all. Dont like the way the WI plate looks on my car and wanted somethin else. Dont want to get pulled over though. :notnice: thanks
  11. B

    Valve body: PA or Lentech?

    I've been trying to decide which I should get. The PA costs less but I can get a Lentech specifically for a high stall converter while there is only one option with PA ( and it is not specified for high stall/OEM ). If anyone has used either, please post your opinion.
  12. B

    Shift points moved after Torque converter?

    Well, i got a 2800 stall PI torque converter in this weekend and now when I am at WOT my car shifts into second REALLY late. So late that I am not going to floor it again until I get this figured out. I have a diablo delta chip that I still need to get programmed, will this solve my problem...
  13. B

    Tranny fluid leaking!! Please read!!!!!!!!

    I installed my tranny cooler today and after I put it in I started my car and put it in neautral to se if there were any leaks, and there is one. :bang: I'm going to try and explain where the leak is coming from as best I can: I disconected the upper tranny line from the radiator and put on...
  14. B

    Where to put tranny cooler

    I have been looking to see how other people installed their tranny coolers to see where I should put mine. I found this site: http://www.2kgt.com/item.php?itemid=21 Is that a good place to put it? It looks like its screwed into the radiator? If any one has a good idea or a link that would be...
  15. B

    Should I install the transgo in a 2001?

    I was planning on installing a torque converter, transmission cooler and shift kit in my car on Sat. and was looking for some install directions when I noticed people saying that a Transgo shift kit will have problems with 99 and newer AODE's. Is this true? If so, is the jerry mod safe? :shrug:
  16. B

    PI torque converter install on AODE

    I have searched the forum and yahoo and I can't find any installation instructions for a torque converter. The directions on the PI web site were not very good. If anyone can help me out that would be great! thanks Its a 2001 gt by the way
Top Bottom
Back
Forums
Menu