Search results

  1. GearHd6

    Slight Stumble Off Idle (Normal?)

    If I blip my throttle off idle I get a slight stumble, under a second but still very noticable. Is this normal? If not, any idea's on how to fix it? Thanks
  2. GearHd6

    Brake Question

    Ok, I just installed some 73mm calipers and cross drilled and slotted rotors. I bleed everything out good and I still seem to have a slightly spongy pedal. It'll lock the front tires up evenly still but just not a hard pedal. The pedal is near the top but spongy if you really stand on it. Maybe...
  3. GearHd6

    Wheel Stud Sizes?

    I need to install longer stud front and rear on my car. Does anyone know the size? I know they're 1/2" but im wondering about the knurl size. Its stock 4 lug set up, nothing exotic here. Thanks in advance.
  4. GearHd6

    Launching with MT DR's

    I put this in Talk but no one responded so i'll try here. Whats everyone doing? I've got the car in my sig with 235's for DR's. I know they're a little small but they actually fit in the fenderwell perfect with no hammering of the lip which is what I wanted. Are you going around the water...
  5. GearHd6

    Launching with MT DR's

    Whats everyone doing? I've got the car in my sig with 235's for DR's. I know they're a little small but they actually fit in the fenderwell perfect with no hammering of the lip which is what I wanted. Are you guys doing a real smokey burnout or just giving it a good hop? I did a moderate...
  6. GearHd6

    Line Lock

    I've got a 91 coupe with the master cylinder with 3 ports coming out of it, 2 on the side and 1 from the bottom. Does anyone know the correct way to plumb a line lock into a master cylinder like this? I've seen them done on the style master with just the 2 ports coming out the side but never...
  7. GearHd6

    Drag Radial Fitment

    I know this subject has been talked about a million times but I think each thread is specific to a certain persons car not ALL cars. Well i've got the 91 coupe listed in my sig and shown in my avatar. Im looking to put drag radials on a set of Weld Draglites. The wheels I have are 15x8 with a...
  8. GearHd6

    Slight Stumble Off Idle

    For some reason if I push in my clutch at idle and rev it up it has a stumble and then the RPM's picks up. Any clues on what mainly cause this type of problem or is that just normal with the injected 302's?
  9. GearHd6

    R-12 Freon

    This thread isnt generally related to Mustangs but im curious. Do automotive shops still provide R-12 freon if the customer whats to pay the enormous price per pound for it? The reason I ask is, i've got a Ford product vehicle that just need the AC topped off. Its a 1994 car and its got the R-12...
  10. GearHd6

    A/C O-Rings?

    Does anyone happen to know the size of the o-rings on the A/C lines of my 91 Coupe? I need to swap them out, my A/C loses charge after about a week. Can I get the o-rings at NAPA or a parts place similar to that?
  11. GearHd6

    Mid to High RPM Break-Up

    Im getting what feels like an ignition break up starting at about 4000 rpms and up. Has anyone had this happen before? The cap, rotor and plug wires are only about a year old. Does the module on the distributor ever mess up or does that just either work good or totally quit and leave you stranded?
  12. GearHd6

    High Idle When Hot

    My car idles perfect when its first started up but once it runs for a few minutes it starts to idle high, right around 1250 RPM's. It doesnt surge, just idles high and the throttle stop screw is all the way backed out. Any clues?
  13. GearHd6

    New Door Weatherstrip

    Has anyone else had a problem with kinking on new door weatherstrip on the top rear most corner where the sharp bend is?
  14. GearHd6

    3550 Pops out of reverse?

    What could cause this transmission to pop out of reverse? It doesnt do it in any other gear. A bent fork? Shifter stops set to tight? Any ideas? Everything else is all rebuilt and shifts awesome.
  15. GearHd6

    T-5 Backup/Neutral Safety Harness

    Im doing an AOD to T-5 tranny swap and im wondering if that T-5 wiring harness is really needed. Can I just tap the AOD back up light wires into the switch on the T-5? And what exactly does the neutral safety switch do seeing you need to have the clutch in to start the car anyway?
  16. GearHd6

    Pilot Bearing or Bushing?

    What do you guys recommend for the pilot bearing application? Some say that the bushing takes more punishment and I was concerned about the bearing drying out after a while. What do you think?
  17. GearHd6

    NOS Activation Question

    Im sorry if this has been asked before but I did a search and only came up with 5 posts that didnt include what I was looking for. Im trying to figure out the BEST way to activate my NX kit on a manual transmission car. The WOT switch seems good except for on launch, I dont want it to really...
  18. GearHd6

    Factory Build Codes, Where?

    Where do you find the codes on a 91 Fox for things like interior color, axle ratio and any other factory options?
  19. GearHd6

    50oz or 28oz??

    I've got the car shown in my sig with a stock 91 engine in it. Its got an AOD in it now. Im trying to figure out how I can tell what weight accessories I have. I've got a complete 5 spd conversion on the way thats used but I want to make sure im installing the proper parts. Is there any way to...
  20. GearHd6

    E cam with stock converter?

    Is it possible to run an E303 cam with the stock torque converter? Or is there a better cam for an automatic car? I dont want to go to crazy anyway because I have emissions to worry about here.
Top Bottom
Back
Forums
Menu