Search results

  1. 8

    Cam Identification

    can somebody identify this 5.0 cam and possibly give me specs?
  2. 8

    Expired 5.0 Explorer Fuel Rail

    5.0 explorer rail up for sale. Came off of a 99 5.0 explorer. Fits many years. $50 shipped. I do take Paypal I'm reached easiest by text 262-729-6860. Mat.
  3. 8

    Tire size question 215/60/15 front 235/60/15 rear?

    All of my tires are cracked and while I was at the local junkyard today for other parts I noticed they had some nearly brand new 215/60/15 (2 of them) and 2 of the 235/60/15. I have an 86 gt 5.0 with the stock 15'' rims. I have searched for 3 hours and got minimal information. I know the stock...
  4. 8

    NOOOO Heat After Heater Core Replacement

    I replaced my heater core because I was getting a fogged up windshield which would then freeze :jaw: It got hot and I had heat before but the coolant on the windshield got real old. Now after replacing the heater I get nothing. By nothing I mean with the controls on "warm" the air doesn't even...
  5. 8

    Its getting cold/heater blowing my engine!?

    A few years ago I swapped engines and it seemed like a good idea at the time to remove all the smog stuff and ac stuff. Since then when I turn my heater fan on only the defrost blows and air. It gets warm so im guessing my heater core is ok but I noticed that the air blows into the engine...
  6. 8

    Turn Signals light up but dont flash???

    86 gt 5.0. My rear turn signals light up like they should but they dont flash. Any ideas? Im confused because my hazards work fine. Is there a different flasher for the turn signals?
  7. 8

    SIGRTN burnt on my A9L, I can fix it but whats the cause?

    I recently converted to mass air and since Im having idling problems I tested for 5 volts reference at my tps. It was there, only .12volts. I opened the computer and sure enough the SIGRTN circuit is fried. I can fix it easily with some solder and a little wire but if I put it back in its gonna...
  8. 8

    TWO A9Ls 1 good 1 bad Runs good on bad one? Is speed density better?

    I got two A9L mass air computers as I converted my 86 gt to mass air. One seems to do what its supposed to as far as correct voltages at tps, priming fuel pump ect...the other one has the fuel pump running constantly (doesnt shut off once it primes) but it responds to throttle and runs way...
  9. 8

    347 stroker firing order???

    I just picked up a 5.0 that has been bored & stroked to a 347. How can I tell if its an H.0. or non-H.O. firing order?
  10. 8

    jrichker or hissin50 can you help?

    I want to make sure my wiring is good to go before I time my car and get it up and running. I think i have a bad ground because when i test any two wires on fuel injectors I get like .12 volts but if I probe the red wire on the injector and probe chassis ground I get 12 volts, is that right? I...
  11. 8

    Is this a picture of a ground or a solonoid wire?

    Can you tell me what this is? I just swapped all my harnesses and I cant figure out what this is...Is it a ground block? Any idea what wire goes to the other side? It reached the starter solonoid but its a black wire with a white stripe...86 gt 5.0
  12. 8

    Are my tps numbers right?

    I get 5v reference on the orange wire and to chassis ground. If I probe the connector at black & orange I only get 0.12v. Is this right? I know the green wire is for setting and the orange should get 5volts reference, correct?
  13. 8

    Fuel pump stopped priming today...KOEO Results help?

    My fuel pump was priming this morning as I was attempting to get the timing set after a motor swap. Its not priming anymore and Ive done some of the testing but I dont know where to go from here. I jumpered the computer test ground and fuel pump test connector but the fuel pump didnt turn on...
  14. 8

    86 5.0 Mass Air Conversion HELP! Do I have cruise?

    I have everything else for the swap done except I'm confused on the VSS wiring. I don't have the same wire color for the vss wire behind the drivers side kick panel.I don't have a orange and yellow on the 8 pin connector, I actually have a orange and light blue one. Also, I don't have a dark...
  15. 8

    Will Carb timing cover work with efi?

    I have a 302 that had a carb on it and Im going with efi. Can I use the carb timing cover thats on there or do I need to put on an efi one? I have the water pump for the existing timing cover that I just need a gasket for, otherwise I have pull the pulley off and my puller broke so to save some...
  16. 8

    Wire harness differnece. Clutch dissengage/nss switch help needed

    I'm putting in a different engine/headlight harness in my 86gt 5.0 because my old one was shot. I almost have it completed but I need help so I posted a picture of the plugs that go into the switch by the clutch pedal (nss or disengage switch???) the new harness doesn't have those two plugs so I...
  17. 8

    8 guage yellow wire going into firewall question

    I have an 86 gt 5.0. Im putting a new wire harness in (also supposedly from an 86gt) and theres an 8guage yellow wire im confused about. On my old harness it starts from the starter solonoid and goes into the firewall but on the new harness it doesnt, it stops and has a female spade connector...
  18. 8

    Wrong o2 sensors for my computer?

    Im putting my stock computer & engine harness back in my 86 gt after it sitting for over a year. Just before I blew the motor I had replaced the o2 sensors but more recently remember reading something somewhere about having to have different o2 sensors for maf vs speed density. That if you run...
  19. 8

    Wiring identification help please!? 86gt

    Im putting a stock engine/ecu harness back in my 86 gt 5.0 and there's two wires im confused about. I got off craigslist and its supposed to be from an 86gt but a few wires are different. In the pics you can see theres a long wire that originates next to the 60 pin connector that is like 5 feet...
  20. 8

    Weird! Blower motor/fan blowing but not blowing

    My heater fan works on all positions and sounds like its blowing but no matter what position i put the controls on it doesnt actually blow any air. Well a very very little bit through the dash pad for the defroster. Its warm but doesnt blow but the fan turns on.....whats wrong?
Top Bottom
Back
Forums
Menu