Search results

  1. Falcon79

    Brake Line Flaring

    Yes, my tool from MAC tools, the cutter is made by craftsman. I've gone through the list of "things to try". Its holding up my project and I'm tired of looking at my stang on jackstands.
  2. Falcon79

    Brake Line Flaring

    Hey guys, I am trying to finish up adding four wheel disc brakes on my 1968 coupe. The one thing holding me back is I need to fabricate a few brake lines and I can't get good flares with any of the tools I've bought. I'm through throwing money at tools and I want to pay someone to do it. If I...
  3. Falcon79

    1968 coupe fuel sending unit wiring

    Bump. Anyone have any knowledge about this? The yellow wire in the pic is the fuel sending unit feed, it travels up through the trunk and the up behind the passenger side wheel well. I'm asking what wiring harness this wire is a part of.
  4. Falcon79

    1968 coupe fuel sending unit wiring

    I recently installed this wiring harness on my 68 coupe: WIRING, TAIL LIGHT HARNESS, 1968, COUPE & CONVERTIBLE :: Wiring Harnesses :: Electrical & Wiring :: Mustang Parts & Accessories Superstore - 1800Mustang There is no connection for a fuel sending unit plug. the only connections are...
  5. Falcon79

    1968 coupe fuel sending unit wiring

    Does anybody know where i can buy a replacement wiring harness that goes from the front and includes the fuel sending unit plug? Its not the harness that has the rear tail lights but another one that I'm not able to find. Thanks
  6. Falcon79

    Neutral safety switch question

    I just replaced the entire rear harness wiring so I ruled that one out. I think the question i was trying ot get answered was about the compatibility of a switch from a '70+ C4 to a '68 wiring harness, the plugs are the same but the mustang vendors sell them as two different parts. one fits...
  7. Falcon79

    Neutral safety switch question

    I have a 68 mustang with a '72 C4, the neutral safety switch came with the tranny. The plug matches my wiring harness but I'm not getting the rear parking lights to come on. Do i need to switch the neutral safety switch to a 68 year switch?
  8. Falcon79

    attaching starter to starter wire

    Hi guys, I was wondering exactly how you attach the starter wire to the starter. Is it a bolt or screw or clip. I need to go get it today so if you know the thread size that would be helpful too. This is for a 1968 mustang with a 302 engine. Thanks
  9. Falcon79

    12V switched power source in 1968 mustang

    Hi guys, I'm almost through installing a duraspark system in my 68 coupe and all that i have left is to splice into a switched 12 volt power source. I want to use the wire coming out from the ignition switch but I have no idea which wire I should use. I'm so close to getting this beast to...
  10. Falcon79

    1968 mustang oil pressure guage connector

    anybody with a picture of the oil sending unit connection?
  11. Falcon79

    1968 mustang oil pressure guage connector

    Does anybody have a pic of what the connection looks like where the engine gauge feed wire connects to the oil pressure sending unit. There are three wires in the engine gauge feed: White/Red goes to oil sensor red/Green goes to positive coil post red/white ?????? Also I'm confused...
  12. Falcon79

    which speedo gear should i use?

    rear tire diameter: running 17x8 wheels from a 2003 GT gear ratio: no sure but should be in the 2.79-3.20 range drive gear: no idea
  13. Falcon79

    which speedo gear should i use?

    I am switching my 68 coupe 6 cylinder car over to a v8. I bought a c4 to go with my 302. Should i use the speedo gear that came with the new transmission? or should i use the one from the 6 cylinder transmission? I know very little about this so if someone can give me an iea what to do that...
  14. Falcon79

    question about my 302 block

    do you know where to get a replacement?
  15. Falcon79

    question about my 302 block

    I have a 91 roller block 302 I'm putting in my 1968 mustang coupe. What is this hex bolt located on the block just above the oil pan, there are four, two on each side. I only ask because I am missing one on the rear passenger side of the block. Where can i find a replacement? or can i just...
  16. Falcon79

    restoring 1968 mustang center console

    Hey guys, I'm restoring the center console of my 68 coupe. I have two questions. Does anybody know where i can get the vinyl prep solution that will allow the new dye to take. Also does anybody know what paint i can use that will match the camera case flat black? Thanks.
  17. Falcon79

    parking brake bracket in rear drums

    1985-91 LTD crown victoria and grand marquis have 10 inch drum brakes, I hear you can get them out of those. Also CJ pony parts sell the arms you are looking for but they gouge you on the price almost $60 a piece!
  18. Falcon79

    C4 transmission question

    Thanks guys
  19. Falcon79

    C4 transmission question

    Hi guys, I got a question about the c4 i just bought, year code says 1974 on the valve body. There is a hole in it that doesn't appear in any of the other c4s I've seen, can anyone tell me what goes there?
  20. Falcon79

    Distributor for a roller block

    What I have in my 91 roller right now is the duraspark setup but I only have the dizzy and not the module, I would replace it with a new duraspark setup if i knew where to get it. Anyone know where i can find one?
View older results
Top Bottom
Back
Forums
Menu