• Mustang Forums
  • 2005 - 2014 S-197 Mustang -General/Talk-

2007 GT: Engine Codes p060b, p2104, p2110

  • Thread starter Thread starter C_GT_OVER9000!
  • Start date Start date Oct 27, 2020
  • Tags Tags
    #technical bama tuner engine codes jlt p060b p2104 p2110 s197 mustang tps sensor
C

C_GT_OVER9000!

New Member
Oct 27, 2020
1
0
1
Lafayette, Louisiana
Oct 27, 2020
#1
  • Oct 27, 2020
  • #1
Recently bought a jlt cold air intake and a bama performance rev ex tuner. First week with the 93 race tune was great. And i dint step on it until i was past 100 miles of regualr driving. Randomly after a week im leaving work one day and i get a wrench light and engine light at 70 mph and cant accelerate anymore. Had to wait hours for someone to bring me my tuner. For the past two month i’ve been going back and forth with bama and sct. After replacing several parts im low on funds and im nervous to bring it to a mechanic cause im broke‍ But the part i replaced so far have been the tps sensor, then the whole throttle body (oem replacement), maf sensor, and accelerator pedal. I checked wires multiple times and cant seem to find damaged ones. Im stuck scratching my head. Can anyone help please. *And it only goes into limp mode after a good while of driving. And usually at stops.
 
O

OchoZero

New Member
Aug 9, 2021
2
0
0
Denver, Colorado
Aug 9, 2021
#2
  • Aug 9, 2021
  • #2

hello everyone. i am new to the group. i just purchased a 2007 mustang GT with upgrade edelbrok supercharger. i getting a code P2104.Throttle actuator​

i looked it up and it say to look a wiring issues. i didn't find any issues with wiring to actuator. i believe the throttle body stays open every time i rev up the engine.
it causes the car to not go anywhere when i hit the gas pedal. the car does not stall. gas pedal does not work. so i have to restart and it works.
what other things can i look for when i take the throttle body off.
i know i have to check the voltage on the actuator. is there a certain number that it has to be at in order to work properly?
if anyone has had this type of issue, let me know what i could look for.
thank you
 
You must log in or register to reply here.

Similar threads

SURGING IDLE / NO IDLE CHECKLIST FOR 1996–1998 MUSTANG GT (4.6L 2V) - Work In Progress
  • Noobz347
  • Aug 30, 2025
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
0
Views
716
1996 - 2004 SN95 Mustang -General/Talk- Aug 30, 2025
Noobz347
SURGING IDLE / NO IDLE CHECKLIST FOR 1999–2004 MUSTANG GT (4.6L 2V) - Work In Progress
  • Noobz347
  • Aug 30, 2025
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
0
Views
872
1996 - 2004 SN95 Mustang -General/Talk- Aug 30, 2025
Noobz347
J
p060b, p2104, p2110 codes - in failsafe engine mode
  • JohnEP
  • Oct 13, 2020
  • 2005 - 2009 Specific Tech
Replies
2
Views
4K
2005 - 2009 Specific Tech Jun 3, 2023
Dino Dino Bambino
J
Wrench light, limp mode, P060B, P2104, P2110
  • Jake's Ride
  • Jul 22, 2020
  • 2005 - 2009 Specific Tech
Replies
14
Views
10K
2005 - 2009 Specific Tech Jun 2, 2023
Toddfly13
T
N
2007 Mustang GT Cold Engine and Hesitation Problem
  • noahgt
  • Nov 17, 2020
  • 2005 - 2014 S-197 Mustang -General/Talk-
Replies
2
Views
2K
2005 - 2014 S-197 Mustang -General/Talk- Dec 24, 2020
McFly2
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 2005 - 2014 S-197 Mustang -General/Talk-
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?