3 pt seat belt question

brtnstrns

Member

Dec 19, 2003

606

11

19

Lewisville, TX

Jul 28, 2004

#1

• Jul 28, 2004

• #1

I got 3 pt seat belts from Andover Mustang. My question is how do I mount the 3rd point, theres no backplate for it. Should I just buy a back plate like the ones that go under the floorboards and use that? The 3rd point being the one that mounts at the shoulder height. I know many people use this setup just wondering how you did it...i've got all the other points figured out, just not that one since the kit didnt come with anything

 

6

65straightsick

New Member

Jun 4, 2004

411

0

0

Montgomery, AL

Jul 28, 2004

#2

• Jul 28, 2004

• #2

You are talking about the top point of the harness I am guessing. I think they make backing plates or reinforcement plate. If I were you I would make my own and be cheap like that. But cheap does not mean good quality. If they offer a plate then get it...hands down.

 

P

PCH_Cruiser

Founding Member

Jul 31, 2002

69

0

0

Palmdale, CA

Jul 29, 2004

#3

• Jul 29, 2004

• #3

You've got two options.
1) Weld a nut / structure to the roof. This will mess up the paint and is the most difficult choice, but some people prefer the pivot above their shoulder
2) Mount it to the back of the door jamb. This doesn't require welding, just drill a hole, and make a backing plate to reinforce it. I chose the second option, and like the setup very much. The belts are comfortable and easy to reach. Here's a link to my website that shows how I installed them.

 

brtnstrns

Member

Dec 19, 2003

606

11

19

Lewisville, TX

Jul 29, 2004

#4

• Jul 29, 2004

• #4

I got my seatbelts from andover but they didnt give me the backplate that you have on yours. I wanna do it from where you have it but where do I get the backplate?

EDIT: nevermind, i saw where you got em...home depot

 

MustangMatt1966

New Member

Mar 11, 2004

1,004

1

0

Orlando Fl.

Jul 29, 2004

#5

• Jul 29, 2004

• #5

I ahve a question, not to steal the thread, but if i wanted to do a 5 point racing seatbelt setup, i guess i would have to weld a bar in the back going across the seats if i dont have a roll cage correct, doing this would give me a place to mount the belts behind me?

 

6

65straightsick

New Member

Jun 4, 2004

411

0

0

Montgomery, AL

Jul 29, 2004

#6

• Jul 29, 2004

• #6

That would be correct mustangmatt, make sure the bar is right at shoulder height so if something goes wrong the seatbelt will pull directly back and not down risking spinal cord injury...that would be bad.

 

MustangMatt1966

New Member

Mar 11, 2004

1,004

1

0

Orlando Fl.

Jul 29, 2004

#7

• Jul 29, 2004

• #7

thanks straitsix, i am planning on doing that in the near future, so its nice to know, i just need the bar, and not a whole role cage

 

6

65straightsick

New Member

Jun 4, 2004

411

0

0

Montgomery, AL

Jul 29, 2004

#8

• Jul 29, 2004

• #8

No problem at all..That is some piece of information I have no regrets letting people know. My mom recently rolled her 2001 ford explorer and it was because she had her seatbelt on that she is still around. If she had gone over the embankment on the bridge she rolled on....well you get the picture.. It is a blessing from God she left with minor scratches from the glass.