• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

351 question

  • Thread starter Thread starter lgbnaf7
  • Start date Start date Oct 23, 2005
L

lgbnaf7

New Member
May 6, 2005
61
0
0
Tacoma Wa
Oct 23, 2005
#1
  • Oct 23, 2005
  • #1
I have a 89 gt convertiable. I am finding out the maintenance was not there on the car from the previous owner. So since the engine will need a rebuild I was thinking of building a 351 and going from there. Here are my questions: What kinda 351 should I look for and Can you make it fuel injecte?
 

jadedinpa

Founding Member
Aug 2, 2002
1,094
0
0
lancaster, pa
Oct 23, 2005
#2
  • Oct 23, 2005
  • #2
depends on your plans. if you are going to swap to a 351, remember that you'll need to change out a lot of things (headers and intake off the top of my head, probably more....). but yes, you can make it fuel injected. for the sake of simplicity, most people stay with the 302, and either bore it out, stroke it, supercharge it, turbo it, or spray it.
 
M

macx

New Member
Jul 18, 2004
228
0
0
SE Missouri near Cape Girardeau
Oct 23, 2005
#3
  • Oct 23, 2005
  • #3
Light truck 351's from maybe mid-94 & up have roller compatible blocks,
although they're not quite as strong as earlier blocks, but still considerably stronger than a standard 302 block. But with one of those you can use stock 302 roller cam hardware and lifters which is lots cheaper than retrofit hydr roller lifters.

If you don't get one that originally had a serpentine belt setup, then
you'd also need to get the serpentine crank pulley and spacer. Look
in www.alternativeauto.com their water box archives for a complete
Ford part # list for that and other stuff. (That and other links are in
the article I linked, below)

Your efi system will plug right in if you use an injection setup on the 351.
If you use a stock 351 or one with just a mild cam, you're probly OK with the 19 lb injectors. But the stock throttle body etc will really choke a 351, even a real mild one.

Awhile ago, I did a search and a Wanted Ad on Corral.net and found 24 lb injectors and a Pro-M larger meter calibrated for 24's used, or the new Pro-M outfit now sells them, too. If you're going mild, you can adapt a GT-40 or Cobra (need one with the interior EGR port) or early Explorer (much like a Cobra & the early ones have the interior EGR port so your system will fit right up & can be had quite reasonable at junkyards & by shopping around the internet) using Weiand/Holley or www.pricemotorsport.com spacer adapter plates. I wouldn't bother adapting a stock 302 intake unless you want the engine to sign off in mid range. If you're going much over 380 horse or so you'd need 30's and at least a 75+ meter and throttle body. Also either the Trick Flow intake or the Edelbrock 351 lower with like a 302 Performer RPM or bigger upper. The TF is a great efi 351 intake.

For a budget mild build, iron GT40's would be good up to maybe 350hp and reasonably priced. If you're going much stouter, then you'd need more. AFR 185's are great for stout 351's. I happened to find a used set of Ebrock 1.9 intakes alum heads for $600, and they're not a WHOLE lot behind the newer "latest greatest tech" heads like AFRs, and my motor is fairly mild so I got what I needed pretty reasonable. Pays to shop around.

If you go an earlier block , you'd need to make sure to get a 351 or 302/5.0 HO flat tappet cam so it has the right firing order - a non-HO cam has a diff order. That's if you don't want to spend the about $400 for retrofit hydr
roller lifters so you can use a roller cam.

Even on a mild engine, you'd need to get the computer dyno tuned to reset some things like the timing curve (reset the parameters to 351 cu in instead of 302, etc which affects the load table in the computer) so you can get it to run right and don't burn it down from too much timing advance etc. - & there's other things but I'm no computer expert. I happened to find a relatively rare 70mm Ford meter made for use with 30's, but I'm still going
to get it dyno tuned to get the cu inches & other things reset inside the computer.

For the rest of it here's how I did mine in an 89 Linc Mk7 which is just a longer Fox chassis.

Any questions, feel free macxx1@excite.com

www.lincolnsonline.com/article144.html

It's more work and expense than going to a bigger smallblock with
Chev & Mopar, but it can be done. Nothing overly difficult.

Everything considered, you could rebuild your 302 with a 331 or 347 stroker
kit for maybe about the same overall cost, and actually have at least as much power cuz the lighter crank/rods/pistons rev quicker than with a 351. (I prefer 331's cuz some - not all - 347's have oil use problems cuz the
piston pin is up in the oil ring groove - if you go 347, get one like Coast I think with the shorter rod but offset pin so you don't have such a bad rod angle which accelerates bore and piston wear on the thrust side cuz the rod is so short) One advantage, however, with a 351 is that you can do a cheap 393
using a ~$250 cast crank, stock 351 rods, and stock 302 pistons. (Just to plant a little evil seed ;-))
 
You must log in or register to reply here.

Similar threads

K
Engine Gt40p vs 180 procomp
  • Kleinjj27
  • Oct 27, 2026
  • Fox 5.0 Mustang Tech
Replies
17
Views
477
Fox 5.0 Mustang Tech Nov 3, 2026
Kleinjj27
K
Electrical Dash wiring
  • RileyDymond
  • Jul 19, 2026
  • Fox 5.0 Mustang Tech
Replies
6
Views
187
Fox 5.0 Mustang Tech Jul 19, 2026
RileyDymond
T
New Guy from Southeast Missouri
  • tcooke11
  • Jan 10, 2026
  • The Welcome Wagon
Replies
1
Views
337
The Welcome Wagon Jan 17, 2026
TomcatPC
A
A/F ratio gauge install questions.
  • AngryH58
  • Sep 24, 2026
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
5
Views
243
1996 - 2004 SN95 Mustang -General/Talk- Oct 22, 2026
Noobz347
9
Engine Donor '00 Mountaineer meet '91 Fox
  • 91firecracker
  • May 11, 2026
  • Fox 5.0 Mustang Tech
  • 2 3
Replies
41
Views
1K
Fox 5.0 Mustang Tech May 28, 2026
91firecracker
9
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?