• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

351w casting question

  • Thread starter Thread starter big_tiger15
  • Start date Start date Oct 28, 2005
B

big_tiger15

New Member
Sep 13, 2004
88
0
0
Arlington, Texas
Oct 28, 2005
#1
  • Oct 28, 2005
  • #1
I search around the web for about an hour last night, and I could not find a casting number for the years 80-93. I am looking at a bare 351w block and he says it came out of a car in the 80s. I am just making sure I know what year it is. I know I could check the height from the freeze plugs. Its one inch correct?

Is there any reason why I shouldn't buy a 351w block that came out of the 80s?
 

BlownFiveLiter

have car, will race....wait, it doesn't run
15 Year Member
Nov 29, 1999
3,133
18
108
Chicagoland
Oct 28, 2005
#2
  • Oct 28, 2005
  • #2
Ford probably used different casting numbers over the years, but I believe up until either 93 or 94, they were non-roller blocks. Being non-roller is the only reason I could think of, but they can be converted with a kit.
 
B

big_tiger15

New Member
Sep 13, 2004
88
0
0
Arlington, Texas
Oct 28, 2005
#3
  • Oct 28, 2005
  • #3
StangGT1995 said:
Ford probably used different casting numbers over the years, but I believe up until either 93 or 94, they were non-roller blocks. Being non-roller is the only reason I could think of, but they can be converted with a kit.
Click to expand...

I was just wondering about how much power the 80s blocks can take. Im not looking to make godly power out of the 351w . I am looking to buy a good bottom end and putting the motor in. Then later on add goodies like aluminum heads, and/or nitrous.
 

BlownFiveLiter

have car, will race....wait, it doesn't run
15 Year Member
Nov 29, 1999
3,133
18
108
Chicagoland
Oct 28, 2005
#4
  • Oct 28, 2005
  • #4
I've heard some pretty high numbers for 351 blocks. Somewhere in the 750HP range?
Definitely a LOT more than a 302 block can handle either way.
 
B

big_tiger15

New Member
Sep 13, 2004
88
0
0
Arlington, Texas
Oct 28, 2005
#5
  • Oct 28, 2005
  • #5
I am not looking to make that much. Maybe 600 when I am all done with it. You might hace heard of high number, but you have no idea what year block they used.
I read a while back in a free mustang mag they made 692 (something close) NA with a 351w. The block was 1969 though.

No Offense but we need someone who knows more about this subject. Maybe someone who took a 351w out of a lincoln and is using the block now. I want to make sure I dont get f'd.
 

BlownFiveLiter

have car, will race....wait, it doesn't run
15 Year Member
Nov 29, 1999
3,133
18
108
Chicagoland
Oct 28, 2005
#6
  • Oct 28, 2005
  • #6
Nah, no offense here man. I wouldn't want you to take large financial risks based upon things I've heard, but haven't done myself
 

pb_paulie_b

Founding Member
May 19, 2001
894
0
0
Chaptico, Maryland
Oct 29, 2005
#7
  • Oct 29, 2005
  • #7
why not get a 70's block? up to 74' they were made stronger. i have 2 351w blocks, a C9(69') and a D4(74'). 80's blocks would have casting codes of E? where the E would mean 80's followed by the actual year it was made. ex. E1 would mean 81'.
 

vristang

15 Year Member
Mar 31, 2005
4,933
101
124
Seattle
Oct 29, 2005
#8
  • Oct 29, 2005
  • #8
pb_paulie_b said:
why not get a 70's block? up to 74' they were made stronger. i have 2 351w blocks, a C9(69') and a D4(74'). 80's blocks would have casting codes of E? where the E would mean 80's followed by the actual year it was made. ex. E1 would mean 81'.
Click to expand...

This is all correct. So is the above post on roller blocks.

The old blocks are getting harder to find however, at least in the Seattle area. It took several months for me to find the 74 that I used for my 408.

If the block is in good condition there is no reason not to use a 80s block for moderate/reasonable power levels. Roller conversions can be done in your own garage using stock 302 parts.

Good Luck
jason
 

pb_paulie_b

Founding Member
May 19, 2001
894
0
0
Chaptico, Maryland
Oct 29, 2005
#9
  • Oct 29, 2005
  • #9
i can get rid of my 74' if someone needs. no wear on it at all. could even go standard bore w/a good honing...PB
 
You must log in or register to reply here.

Similar threads

351w aluminum oil pump?
  • Kid wita 5oh
  • Oct 28, 2025
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
3
Views
269
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Oct 28, 2025
Mustang5L5
Engine Forged flat top pistons from 5.0 fit a 351 build?
  • PonyGTrider
  • May 22, 2025
  • Fox 5.0 Mustang Tech
Replies
17
Views
2K
Fox 5.0 Mustang Tech Feb 1, 2026
PonyGTrider
J
Engine 4.6 Running rough at half throttle
  • jake411
  • Aug 3, 2026
  • SN95 4.6L Mustang Tech
Replies
5
Views
312
SN95 4.6L Mustang Tech Oct 20, 2026
DangStitches
D
Engine A/C QUESTION
  • Mindseye007
  • Jun 5, 2025
  • Fox 5.0 Mustang Tech
  • 2 3 4
Replies
60
Views
3K
Fox 5.0 Mustang Tech Jun 22, 2026
nicholase
Z
Progress Thread zeth194 - New Guy on the Block
  • zeth194
  • Mar 19, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
10
Views
773
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Apr 26, 2026
LILCBRA
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?