351W Windsor Motor

My friend who got the ball rolling for me to do the 351w swap went 12.70's with his combo: rebuilt 351, 10:1 comp, fords n351 cam, edelbrock performer rpm heads, trick flows efi manifold, tko and a set of 4.10's that he now hates. Now you guys may not think those are good numbers but you guys may forget that when you are 5800' above sea level stuff does kinda run out of breath up here. His car if full weight, subs in the hatch, and ran on some shatty road racing slicks he got for free. Trap speeds were in the 105-108 area too.
 
First off, for sure. The bigger the better, (as long as you're going 351w anyway). (i.e. stroke it).
As far as bolting on the 302 parts, (i.e. heads), Don't do it. Bigger the engine, the better the heads have to be. Basically build the engine around the heads.
Granted, if it's going to be a street car, or street/strip, you can calm down quite a bit on that, but still, why hinder yourself hp/tq wise with a HUGE stumbling block being built in.

In either case, I run a 418. Made 711 horse, and 565 ft lbs. tq. N/A. Best et (on motor), is 9.62 @ 141 mph. with a 1.34 60'.
With a little 150 shot, it went (with torque converter screaming holy hell, and wrong gears for the juice), a 9.0 @ 149.88 mph. with a 1.28 60'.

302 to 351, absolutely. 351+, why not! ;>)
 
Race only, sorry.

Sorry to say it's a race only setup. Nothing really radical, but it has no lights (other than mandatory rear lite as per NHRA/rules), and no turn signals, /heater, etc, etc. If it doesn't make it go fast, it ain't on it.

As far as a setup.
It's a dart 351w block. Eagle stroker kit, (#14127). Custom Ross pistons, 14 to 1. AFR 205 heads done by Ryan. Victor sr. intake (also ported by Ryan). Biggs prepared 950 holley. Cam is a solid roller Isky, custom ground. 765 lift. (fairly big). Harland Sharp roller rockers. ( All msd ignition. Hooker super comp headers. Canton oil pan/pickup.
Trans is a C4 (built by me), with mostly PA internals. A TCS 8" 5500 stall converter.
Rear end is a narrowed 9" w/spool, and 4.30 gears.
Slicks are 31" x 11.5 x 15s.
Car weighs 2500 pounds, (well, it did before I put the dart block in last winter). Probably weighs at least another 50 or so more now.

If you need any more/other info, lemme know. Lots of pics too if ya want.
:nice:
 
Nice set-up,we got something similar (we drive it occasionaly on the street)

DART Iron Eagle block (2.79" main,9.5" deck),Eagle stroker kit,JE pistons (with TFS valve relief a -5cc dome,bout 12:1),heads now are TFS "R" (flowed 380In/260Ex @.700),Cam Motion solid roller (.737In/.724Ex , 273*/284* @ .050 ,112* LSA),Super victor (box stock,will kill us I know :bang: ),BG 950 Race Demon RS,Kook's 2" headers (going with a 3.5" exhaust).

And my favorite part...a NOS Pro Shot Fogger (with Wilson bust panel/1.75" spacer combo) :D

Trans is a PA Super Comp C4 with a PTC 8" converter.Its got the 8.8" right now,still with a Eaton and 28 spline axles! :shock: But going to a 35 spline axles with a spool.

M/T 28"X10.5"/15" :banana:

Cars about 3200lbs with driver.

We were runing TEA ported Track Heats (flowed 310/235 @ .600) and a CAm Motion hydrolic roller cam (.604In/.585Ex , 254*In/263*Ex @ .050 ,111* LSA),and BBk 1 3/4" headers (with were ok,they were actualy for 5 speed,but worked with the C4?)
 
drag79stang said:
Rear end is a narrowed 9" w/spool, and 4.30 gears.
Slicks are 31" x 11.5 x 15s.

If you need any more/other info, lemme know. Lots of pics too if ya want.
:nice:

Can I get a pick of the rear?

Is it still stock suspension,or is it a 4 link/ladder bar set-up?
 
It's a narrowed ford 9". Mark Williams axles.
The suspension is an ancient Comp. Eng. ladder bar setup. Comp. eng. 3 way shocks, and I swap between the 100 pound and 150 pound coil over springs, (depending on track).
As far as pics, gimme an email address, I'll snap some off for ya.
 
drag79stang said:
It's a narrowed ford 9". Mark Williams axles.
The suspension is an ancient Comp. Eng. ladder bar setup. Comp. eng. 3 way shocks, and I swap between the 100 pound and 150 pound coil over springs, (depending on track).
As far as pics, gimme an email address, I'll snap some off for ya.

[email protected]

And thanks,I got a junker 88' coupe 4 cylinder that Im thinking of building for local bracket racing.I would like to do one of them new ladder-links.
 
drag79stang said:
I'll snap some off and ship them out tonite.

Any sorts of pics (besides MY rear end)?, would you like to see, preference wise?

I have a few in the stangnet gallery here. :>)

Looks good,thanks.

You know bout how much its narrowed,compared to a stock one?