5.0 Compression test & head gasket question

chepsk8

Founding Member
Jan 15, 2001
2,203
3
49
Easton, PA
I have a Factory Five Cobra Replia with a 1988 5.0 converted to carb. Radiator is a new 3-row, with a 16" electric fan. I have had an coolant loss problem for a while. Last year, I pulled the intake, and found ripped gaskets by the front coolant cross-over, and brown foam on the PCV & intake. Once this was fixed, the problem went away. After open-tracking the car a few days back, did I have problems again.

Here's where I stand:


OK, ran the cylinders last night with the intake off.

Cylinders 2,3,4,5,6,7 were all 155 to 165 (Not bad for 200K+ miles!)
#8 was 145-150
#1 was 140-145

After each test, I let the guage sit for 5 minites to see if there was any pressure drop. Only #1 very, very slowly lost 3 lbs during that time, but I could not hear any hissing or gurgling noise.

A visual inspection showed the following:

Spark plugs show no iron depisits, just the car running rich.
My Moroso "T" is still intact, and not leaking
All intake manifold gaskets intact & not broken
PCV valve clean, no brown foam
Underside of intake clean, no brown foam.
The only thing I did not get to was opening the oil drain plug to check for water, but it seems unlikely.

So, based on the above, I have two thoughts:

#1 - I just had too much advanced timing in it, not enough coolant, the coolant was mostly water, my catch tank allowed air to be pulled into the cooling system, and my location for the temp gauge was in the wrong spot(rear of manifold). Put it back together with the temp gauge up front, make sure it's full of good coolant, and go on my way.


or


#2 - I remember hearing somewhere that 5.0's to kill head gaskets in the forward cylinders (#1 & #8) where the water jacket is, and mine could only have a very small opening, but enough to cause my problems.

What's your take?


Many, many thanks from an old Classics guy!:SNSign:
 
With the compression readings you have, I would not suspect head gasket problems.

Fox box 5.0's have a air dam located below & in front of the radiator. It isn't anything more that a 3" piece of stiff plastic that is as wide as the radiator. It does help direct the airflow into the radiator. I don't know if FFV's use the same scheme, but you might want to look back at the kit plans.

Electric fans:
Electric fans need either a fan shroud that covers the backside of the radiator, or need to be mounted flush to the core with no gaps. The reason is that the fan should suck air through the radiator and not from the gaps between it and the core.
 
I would think since the nose is fully ducted to the radiator, it creates a "ram" for the radiator. Also, I did put the fan in the Mustang shroud, and it keeps it cool while sitting.

If indeed I did have a head gasket issue, what would my typical readings be, and how fast would my pressure drop?
 
Blown head gaskets will give 25-75 PSI max pressure. The pressure would not hold at all.

If you have any doubt about the head gaskets, see the link in my sig. One of the tech notes on my website is how to build your own blow down compression tester. It puts regulated air pressure in the cylinders and measures the pressure drop.
 
Many Thanks for your help!

In your opinion, would my heating up on the track be a result of low coolant & too much timing advance (I do not know exactly, but with a Unilite Dist w/no vac advance, I think I am somewhere about 15 degrees btdc), and the result of just beating it?
 
I would suspect a low coolant problem first.

Is the car set up so that the top of the radiator or filler is at or below the level of the engine, specifcally the thermostat housiing.

If so, it may be hard to completely fill the system. It may take several triies, or a vacuum fill.

My Capri did this a while back, would run hot, etc. It leaks a good bit over a couple months, and does not get run much these days. A ten mile drive finally burped the air out and its been fine for several weeks, idles ok with the ac on. I usually fill it two or 3 times, dead cold, with the cap off, until the thermostat opens. Its worked this way for 25 years and 260k miles over 3 engines.

On a stock 5.0 car, any of the myriad hoses can weep at the connections, and cause a slow loss of coolant. My particular issue is the splice I have in one of the the heater hoses.