• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

5 lug Rotors??

  • Thread starter Thread starter asecretfile
  • Start date Start date Sep 15, 2008

asecretfile

New Member
Feb 11, 2007
228
0
0
Sep 15, 2008
#1
  • Sep 15, 2008
  • #1
Friend of mine is giving me his 5 lug rotors off the front of his 4 cyl 89lx. (he started it as a project then abandoned it) He said the dust shields and all are stock 4 cyl ones. My problem is on my 87GT the dust shields look different and it looks like the bearings inside are a little smaller on the 5 lug rotors he has. When I try to install it the rotor is rubbing. It doesnt rub on his 4 cyl car, I measured and the spindles are exactly the same length and the only thing I can think of is the dust shield is shaped a little different.

If I try to use my GT bearings it fits but doesnt allow the smaller bearing on the outside go in far enough onto the spindle to get on the slotted washer, nut and cotter pin

any ideas?

thanks
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,371
18,119
224
Massachusetts
Sep 15, 2008
#2
  • Sep 15, 2008
  • #2
4-bangers use 10" brakes while GT's use 10.8" brakes.

If you really want to use them, you'll have to remove your spindles, calipers and lines and downgrade to the 4-banger 10" stuff.

His rotors are off an 80's 4-banger ranger. If you want direct swap 5-lug rotors, you need 10.8" rotors off an 84-92 Mark 7.
 

asecretfile

New Member
Feb 11, 2007
228
0
0
Sep 15, 2008
#3
  • Sep 15, 2008
  • #3
Well, it seems to be hitting on the backside, does it even with the dust shield removed. (did that just to test) and also his rotor although its smaller in overall diameter, is taller maybe 1/2" as in when laying flat on the ground compared to my GT rotor



so an off the shelf 92 Mark 7 rotor will work and not "bottom out" so to speak like my current ones?

thanks
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,371
18,119
224
Massachusetts
Sep 15, 2008
#4
  • Sep 15, 2008
  • #4
If your 87GT is stock, then yes, a Mark 7 rotor (or 84-86 SVO rotor) is basically the same rotor with a 5th lug attached
 

asecretfile

New Member
Feb 11, 2007
228
0
0
Sep 15, 2008
#5
  • Sep 15, 2008
  • #5
ok thanks

are his 4 cyl spindles deeper or something, allowing them to fit on his but not on mine? Measured 3-3/4 spindle length on both our cars. Because I noticed on the bearings they have the same inside diameter but my GT bearings outside diameter is a tad larger
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,371
18,119
224
Massachusetts
Sep 15, 2008
#6
  • Sep 15, 2008
  • #6
Yes, the 4cy spindles are completely different than the 87-93 V8 spindles.


They are the same spindles used on 79-86 Mustangs.
 

asecretfile

New Member
Feb 11, 2007
228
0
0
Sep 15, 2008
#7
  • Sep 15, 2008
  • #7
10-4 thanks for all the help
 

asecretfile

New Member
Feb 11, 2007
228
0
0
Sep 16, 2008
#8
  • Sep 16, 2008
  • #8
Mustang5L5 said:
If your 87GT is stock, then yes, a Mark 7 rotor (or 84-86 SVO rotor) is basically the same rotor with a 5th lug attached
Click to expand...

is this right?

O'Reilly Auto Parts - Shopping

got that under an 84 SVO
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,371
18,119
224
Massachusetts
Sep 16, 2008
#9
  • Sep 16, 2008
  • #9
Can't see what you pulled up, but i searched and it was BD60789 on there.


Just for the hell of it, check a 1990 Mark 7, with and without ABS. Sometimes one of them is much cheaper for some reason. Get the cheapest. ABS or not won't matter at all.
 

asecretfile

New Member
Feb 11, 2007
228
0
0
Sep 16, 2008
#10
  • Sep 16, 2008
  • #10
Mustang5L5 said:
Can't see what you pulled up, but i searched and it was BD60789 on there.


Just for the hell of it, check a 1990 Mark 7, with and without ABS. Sometimes one of them is much cheaper for some reason. Get the cheapest. ABS or not won't matter at all.
Click to expand...

ok thanks

would my GT bearings fit?
 

Mustang5L5

That is…until I whipped out my Bissell
Mod Dude
Feb 18, 2001
43,371
18,119
224
Massachusetts
Sep 16, 2008
#11
  • Sep 16, 2008
  • #11
They should. You might want to purchase rear rotor bearing seals as mine didn't come off in one peice when i ran this setup.

I bought the Mark 7 rotors, used my original bearings and new seals.


I eventually ditched it for cobra stuff
 
You must log in or register to reply here.

Similar threads

8
87 lx 4cyl to v8 project 4 lug disc conversion questions
  • 87lx428
  • Mar 24, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
2
Views
629
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Mar 25, 2026
87lx428
8
J
2003 convertible front brakes sticking
  • jamesbanasky
  • Jul 9, 2025
  • SN95 V6 Mustang Tech
Replies
2
Views
430
SN95 V6 Mustang Tech Sep 6, 2025
jamesbanasky
J
Y
Resolved 5 lug conversion
  • Ybfav84
  • Dec 21, 2024
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
4
Views
704
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Dec 21, 2024
AeroCoupe
P
Suspension Different height ball joints?
  • pindude80
  • Jun 10, 2024
  • Fox 5.0 Mustang Tech
Replies
15
Views
3K
Fox 5.0 Mustang Tech Jun 12, 2024
limp
Cobra Brake Conversion - Spare Wheel/Tire Search
  • AeroCoupe
  • Aug 2, 2026
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
Replies
7
Views
503
1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk- Sep 2, 2026
AeroCoupe
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?