67 Super Snake Project

67FBack · May 9, 2006

I am finally able to get started on my 67 Super Snake Project.

Sent the car off to the media Blaster 5 weeks ago. Got it back yesterday. Nothing but virgin metal

67FBack · May 9, 2006

Epoxy Primered

After much thought, I decided to go ahead and epoxy primer everything. No sense in having to remove all the rust again. Plus it makes me feel like I have accomplished something

85 Turbo Bird · May 9, 2006

gotta love the sight of a virgin stripped... ... I mean the car of course

danewers · May 10, 2006

wow. enough said. hahaha i am jealous. my dream is to start with a '67 fastback shell and build it up with all new parts.

danny clemens · May 10, 2006

Was your car on a trailer heading down Interstate 65 in Alabama Sunday?
I saw a 67 or 68 primered shell but I was headed north and it was headed south so I didn't get a good look at it. BTW it looks good.

JC6715 · May 10, 2006

Car looks great, wish I could do that to mine...

Question: Did you cut those two long ovals near your cowls at the top of the firewall to gain access to the dreaded cowl area without having to drill out all the spot welds?

I just went and looked at my '67 coupe and I don't have those holes...

Just curious. Thanks a lot!

67FBack · May 10, 2006

danny clemens said:
Was your car on a trailer heading down Interstate 65 in Alabama Sunday?
I saw a 67 or 68 primered shell but I was headed north and it was headed south so I didn't get a good look at it. BTW it looks good.

No, I live in Texas. And thanks.

67FBack · May 10, 2006

Cooling Vents

JC6715 said:
Question: Did you cut those two long ovals near your cowls at the top of the firewall to gain access to the dreaded cowl area without having to drill out all the spot welds?

Yes I cut them out. Two reasons, one to gain access. And two, adding a little more cooling for the engine. Unique Performance, who builds the Shelby authorized 427 Super Snake, reports an additional cooling of 6-8 degrees by adding these vent holes. It uses the high pressure at the base of the windshield to force air down through the cowl and into the engine bay area.

Edbert · May 10, 2006

VERY nice Richard!

Call it a "stealth cowl" hood, the extra cooling is gonna be necessary during those central Texas summers too. Are you puting a 427FE or a 427W into your snake? You doing all the work yourself or farming it out to a shop?

JC6715 · May 10, 2006

AWESOME!!! Thanks for the info, looks like I got myself a little project this weekend...

67FBack · May 10, 2006

Edbert said:
VERY nice Richard!

Call it a "stealth cowl" hood, the extra cooling is gonna be necessary during those central Texas summers too. Are you puting a 427FE or a 427W into your snake? You doing all the work yourself or farming it out to a shop?

427FE Shelby Aluminum big block 482ci with S/C. I am doing everything except the finish body layer and the painting.

PS. I got your wiring diagram. Thanks for making it available.

EDIT: ci

Edbert · May 10, 2006

Alooominum 468ci with blower, and all work done yourself? You sir have that rare combination of budget AND time. I can never seem to get both together, right now I have budget but no time.

Good luck with the wiring, I give no warranties, keep the extinguisher handy

JC6715, be aware that if you use your interior vents you'll be pulling in some very warm engine air too.

JC6715 · May 10, 2006

Thanks Edbert

I hadn't thought of that... However, I don't use the vents and I really like the idea of a little cowl access and some cooling for the engine bay. Good looking out, I appreciate it.

67FBack · May 13, 2006

I went ahead and extended the front frame rails toward the rear with some heavy gauge metal. Then I will install the inner floor supports over the heavier duty frame rails. This is the point that the Sub-Frame brace will attach and tie in to the rear spring mounting point.

I fabricated the rails using a plasma cutter and a square to guide the cutter for a straight cut.

67FBack · May 20, 2006

Torque Boxes

I installed two new torque boxes. You sure can have some unexpected rust underneath the old ones

67FBack · May 20, 2006

Lower Shock Tower Braces

I also added the lower shock tower braces.

Sicarius428 · May 22, 2006

Looks very nice! makes me wanna tear my Mach1 apart... Missing the whole funds part though. How much was it to get your body blasted and epoxy primered?
Kevin

HMM · May 22, 2006

Car looks great! Can you give me a little info on that lift? I've been looking around for one but I haven't made a decision on which to buy yet. Would you buy the same make/model lift again?

67FBack · May 22, 2006

Sicarius428 said:
Looks very nice! makes me wanna tear my Mach1 apart... Missing the whole funds part though. How much was it to get your body blasted and epoxy primered?
Kevin

I found a guy close to San Antonio and he did the media blasting (not sand) for $600. It did take him 4 extra weeks to finish the job (because of outside problems), but he did a good job. Even did the doors and 35 other small pieces.

I did the epoxy primer. It took me 3 quarts of PPG DP90LF. 2 just wasn't enough.

I hear you on the funds. I am just lucky that my wife is allowing me to spend the amount of money I going to spend. (Mortgage the house!!!!!

, just kidding).

67FBack · May 22, 2006

HMM said:
Car looks great! Can you give me a little info on that lift? I've been looking around for one but I haven't made a decision on which to buy yet. Would you buy the same make/model lift again?

I found this lift on sale for $1469. It is from American Automotive. It is the TP09A and normally costs $1599. And yes, I would buy the same model again. It is a very good lift. And to me, well worth the money. The rotisserie is also worth the money, even more so.

You need 220v and at least 4" thick concrete. To install you would need a hammer drill and ordinary shop tools. Before you put up the posts, there is a left and a right (for the mounting of the power control).

The whole lift weighs over 700 lbs. You will need to get it off the truck somehow. Even taking the delivered "package" apart, the main posts are still very heavy! (Heavier than 2 people can carry).

Edit: Weight could be almost twice that. I am just guessing, but it is extremely heavy!

67 Super Snake Project

New Member

Attachments

New Member

Attachments

Member

Member

Member

New Member

New Member

Member

New Member

Member

New Member

Attachments

New Member

New Member

Active Member

New Member

New Member

New Member

Similar threads

Privacy & Transparency

Privacy & Transparency