• Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech

am i doomed?

  • Thread starter Thread starter carbed87
  • Start date Start date Aug 20, 2005

carbed87

Member
Jun 5, 2005
215
0
16
Aug 20, 2005
#1
  • Aug 20, 2005
  • #1
just a quick question...




alright, so after i put my cast-iron gt-40's on and felt an overall power LOSS, as well as stil not getting them to run right, i have thought about just putting my stock ones back on. i was just wondering if i would have to change out any of the gaskets i put in under 50miles ago. i mean, they havent even been in there twoo weeks, so do you think they'd be alright being reused? just thought i'd ask.
 

DMAN302

My mom says thanks for the pearl necklace.
Nov 8, 2003
2,120
2
59
windsor, Canada
Aug 20, 2005
#2
  • Aug 20, 2005
  • #2
you lost power because somthing during the swap was not done, or done incorrectly. Swaping heads will only help at this point if you manage to stumble across somthing you may have forgotten during the initial swap. Root cause could be vac leak, ground loose missing (O2 ground wire was off for me...huge difference when corrected), could be incorrectly set up valvetrain..COULD be lost of things...you need to make a list of possibles and walk through cheking them all off. I once found a vac leak on my little girl after honestly well over 5 time checking..right in the passenger fenderwell..5th time was the charm, end result my car idled and ran great for the first time in months.
 
T

TheUser

Active Member
Jul 25, 2003
1,859
1
36
Springfield, MO
Aug 20, 2005
#3
  • Aug 20, 2005
  • #3
I agree w/ DMAN - you should not have lost power by just upgrading heads.

Don't be hard on yourself and I'm sure it was an honest mistake, but something is wrong.

Let me ask this: Did you torque your rockers down using the proper method? If you're not sure, you could search on stangnet and find the best method...I'd try to find a post where Michael Yount has written the method out - I know he did so for me a couple years ago. Even if you used the proper method, they can still possibly loosen; mine were loose one time and I couldn't even get it out of the driveway - I don't think I torqued them at all though lol - rookie mistake.

Are you sure you have your distributer installed correctly? What is your timing set at? What is your fuel pressure? What is your spark plug gap? Did you get all of your connectors hooked back up? What's your TPS voltage?

As DMAN pointed out, make sure you have all of your grounds hooked back up. Never hurts to have too much ground; I got a 4ga starter wire from autozone and attached it to the timing cover where the stock battery ground is and ran it to the firewall. I can't remember the length - but I believe I got one around 36" or so - just measure and see how long you want yours if you want to do that.

Re check the torque on your lower intake as those bolts often loosen up up after heating and cooling a few times - gotta pull the upper to check; however, I doubt that's the cause of your problem.

Possibly the most important: Do you have any check engine codes? If you haven't pulled them, here's a method outlined by the infamous Jrichker showing how to do it w/ just a paperclip or jumper wire: http://forums.stangnet.com/showthread.php?t=566924 - 4th post down

Post back up w/ questions/results.

Good Luck
 

thumper460

Founding Member
Jul 24, 2000
3,022
2
56
Orange Park , Fl
Aug 20, 2005
#4
  • Aug 20, 2005
  • #4
check it out like the above!! most of the time it IS just a overlooked "Little" thing!! As far as re using the gaskets...?? take a chance and have to do it AGAIN!! I have, however, reused the GOOD felpro intake and head gaskets with " high Tac " spray on them and RTV silicon... but... like a I said .. Take that chance????

Just me..........................

Thumper
 
S

ss93cobra

Founding Member
Apr 10, 2002
1,422
1
0
Wilmington NC
Aug 20, 2005
#5
  • Aug 20, 2005
  • #5
 

txstang84

15 Year Member
May 21, 2005
1,639
42
69
Tuscola, tx
Aug 20, 2005
#6
  • Aug 20, 2005
  • #6
X4
 

mondos90lx

Member
Nov 18, 2004
243
0
16
Stoneham Massachusetts
Aug 20, 2005
#7
  • Aug 20, 2005
  • #7
x8
 

carbed87

Member
Jun 5, 2005
215
0
16
Aug 20, 2005
#8
  • Aug 20, 2005
  • #8
any other input other than how stupid i am?
 

CManT1914

New Member
Feb 5, 2004
3,172
2
0
Killeen, Texas
Aug 20, 2005
#9
  • Aug 20, 2005
  • #9
carbed87 said:
any other input other than how stupid i am?
Click to expand...

They're not saying you're stupid, they're agreeing with Thumper, if that's what you meant by your last post.

What all did you do when you did the heads? Did you do the cam at the same time? Or did you already have it in there? I'd definitely pull the codes and see what's going on. You could also try a compression test to see if maybe your rockers are too tight causing the valves to not close fully.
 

carbed87

Member
Jun 5, 2005
215
0
16
Aug 20, 2005
#10
  • Aug 20, 2005
  • #10
no, i had the e-303 in there before, and i shouldn't have tightened one of the rockers too tight, because i tourqued them all down to 20lbs with a "click-click" tourque wrench
 
You must log in or register to reply here.

Similar threads

B
Engine Strange Noise
  • burntokita
  • May 8, 2026
  • Fox 5.0 Mustang Tech
Replies
8
Views
548
Fox 5.0 Mustang Tech May 11, 2026
keel
Most ridiculous / dishonest work you have heard a shop recommend?
  • SchwarzStock
  • Jul 19, 2026
  • Off-Topic Hangout
Replies
4
Views
143
Off-Topic Hangout Jul 20, 2026
SchwarzStock
S
Need help asap
  • shaggyman65
  • Dec 24, 2025
  • 1996 - 2004 SN95 Mustang -General/Talk-
Replies
2
Views
316
1996 - 2004 SN95 Mustang -General/Talk- Dec 24, 2025
shaggyman65
S
M
Resolved 1988 Foxbody - Overheating Summer
  • MDrisc
  • Oct 26, 2025
  • Fox 5.0 Mustang Tech
Replies
16
Views
1K
Fox 5.0 Mustang Tech Jul 17, 2026
fasterthangas
F
L
95 gt engine vibration
  • lenzgt
  • May 11, 2026
  • 1994 - 1995 Specific Tech
Replies
6
Views
378
1994 - 1995 Specific Tech May 26, 2026
lenzgt
L
Share:
Bluesky Email Share Link
  • Mustang Forums
  • 1979 - 1995 (Fox, SN95.0, & 2.3L) -General/Talk-
  • Fox 5.0 Mustang Tech
Menu
Log in

Register

  • Forums
  • What's new
  • Media
  • Resources
  • Contact
  • Sponsor
X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?

X

Privacy & Transparency

We use cookies and similar technologies for the following purposes:

  • Personalized ads and content
  • Content measurement and audience insights

Do you accept cookies and these technologies?