Anaylize my time slip please:)

niklid05 · Sep 3, 2006

My brother and I took my car to Maple Grove a couple weeks ago, this was my first time at a track. The cars mods are: BBK 1 5/8's lt's, bbk o/r h pipe, flows(crush bent tailpipes), hurst shifter, 3.27's, (it also has 17 in cobras, with toyo proxie 4's on). Full interior, spare and jack, pdl, pmirror, and manual windows.

My time:
rt: .395(lol)
60: 2.477(LOL)
330: 6.432
1/8: 9.690
mph: 76.3
1000: 12.490
1/4: 14.647
mph: 95.16

My question is pretty much is there any room for improvement with what I have right now. The mph seems a little high for 14.65, but I dunno thats why I am asking you guys to check it out.

stprorolla49 · Sep 3, 2006

your mph seems spot on for the ET man...with a better 60', you should me low 14's...fwiw, i ran 14.2@96 with a 2.01 60' with similar mods to you...

Lyncher · Sep 3, 2006

With a good 60' I definatly think you can break into the high 13's...dont forget stprorolla ran a 14.2 but his car weighs significantly more than your notch

mob · Sep 3, 2006

Yea, mph may be just a tad bit high for the et but its not high by any means. And that 60' is BAD, get the 60' down and you should probably be able to hit low 14's. Thats about it.

mob · Sep 3, 2006

Lyncher said:
With a good 60' I definatly think you can break into the high 13's...dont forget stprorolla ran a 14.2 but his car weighs significantly more than your notch

How dare you get his hopes up like that?!?!

niklid05 · Sep 3, 2006

nah, Im not looking for 13's atm but, I could get close. I wanna throw in a set of 3.73s and a B or E cam just for ****s and giggles, and hope I get a low 14. Mob is right, the 60 is terrible LOL. I knew it as soon as it happened, I was thinking right after I launched, that it was gonna be a 3 second 60' lol. What kind of gains would I pick up with 3.73's and a mild cam on a stock motor. I know I gotta convert to mass air. I have an meter and ECU sitting in my garage, I just need the other stuff.

BTW I am running stock tire pressure on the proxies would lowering them to 25 psi help a bit?

gcwh02 · Sep 3, 2006

yea, you can definately cut a few tenths off with a lower 60. Do you go to KU or do you just live in the town. Im a sophmore there

niklid05 · Sep 3, 2006

I live here. Are you staying in town or do you go home?

Lyncher · Sep 3, 2006

mob said:
How dare you get his hopes up like that?!?!

With a really good driver I think tis possible... lol maybe im optomistic

gcwh02 · Sep 3, 2006

niklid05 said:
I live here. Are you staying in town or do you go home?

I commute. Do you keep your stang at school?

niklid05 · Sep 3, 2006

gcwh02 said:
I commute. Do you keep your stang at school?

No I mean this is my hometown, I dont go to school.

BTW What do you guys think about an alphabet cam on a stock motor and 3.73's? Mob, you have both what do you think Ill pick up with those two?

Curse · Sep 3, 2006

I agree with everyone else, get that 60ft down and you will go low 14s maybe high 13s.

The 3.73s with a sticky tire should easily net you mid 13s. Good luck

niklid05 · Sep 3, 2006

Curse said:
I agree with everyone else, get that 60ft down and you will go low 14s maybe high 13s.

The 3.73s with a stick tire should easily net you mid 13s. Good luck

What about the cam? How much would a B or an E cam help with a stock motor except maybe an older eddy upper and lower and a 65-70mm tb?

grey5.0beast · Sep 3, 2006

Not much, just a cam really wouldn't benefit your motor with stock heads and intake..

gcwh02 · Sep 3, 2006

depending on how much money you want to spend will determine what you wanna do but I think the TFS h/c/i kit will be good.

90_Red_LX · Sep 3, 2006

Low 14's if you cut a 2.0 or 2.1 60' time. The launch is critical to a stock fox since it leaves a lot of power to be desired up top to make up for a bad launch.

Flavadave4 · Sep 3, 2006

sounds about right.......I have run 14.41 at 98.20 with a 2.28 60' with about the same mods as you

I need practice and so do you!

willys1 · Sep 3, 2006

A set of DR's should stop the wheel spin. Get those 60's below 2.0 and your easily in the 13's!!

BlownStangGT · Sep 3, 2006

I would think you can get a little more out of the car, my old 91 gt has shorty headers, h pipe, flows, pullies and with 2.73's it went 14.1 at 100 mph with a 2.3 60'...I gotta get to the track sometime when I have time this fall...I work in reading and pass maple everyday haha

90_Red_LX · Sep 3, 2006

I don't see a 13 second time in his car w/o a sub 2.0 or better 60' at least. I think you need a little more power to get it there. Low 14's are in the car as it sits though.

Anaylize my time slip please:)

New Member

Active Member

New Member

the guy who hits on his mom

the guy who hits on his mom

New Member

New Member

New Member

New Member

New Member

New Member

Member

New Member

Cookies should never be DUNKED!!!

New Member

Member

Active Member

Active Member

REPEAT

Member

Similar threads

Privacy & Transparency

Privacy & Transparency